How To Find Correct 8" Wheel for Taylor-Dunn Hub

Question

Question:

Will this bolt pattern fit a Taylor-Dunn hub?

asked by: Jerry

0

Expert Reply:

The Steel Trailer Wheel part # AM20027 has a 5 on 4-1/2" bolt pattern which is very common. The other common bolt pattern is 4 on 4" like the Steel Trailer Wheel part # AM20021. If you are unsure of your bolt pattern you can simply use the help article attached below which shows you how to measure, it's very simple.

expert reply by: Conner L

0

Answer 1

The difference between load ranges varies based on the tire size and brand. When comparing two tires of the same size and brand, a load range D tire will always have a greater weight capacity and psi rating than a load range C. However, when…

view full answer...

Answer 2

The tire size 16 x 9.5-8 has a diameter of 16", a section width of 9.5" and an 8 wheel. The closest tire size that we have to that is 215/60-8 like the Kenda 215/60-8 Bias Trailer Tire with 8" Galvanized Wheel #AM3H300 that you…

view full answer...

Answer 3

The Kenda 5.70-8 Bias Trailer tire with 8 Inch White Wheel will work well as a replacement tire for your burden carrier based on the information outlined in the manual. All of the wheels we offer in this size have a solid center wheel, not a spoke…

view full answer...

Answer 4

If you just wanted to get the tires and not replace the wheels you can use #AM10013. This is a 5.70-8 tire, load range D, with a capacity of 1,075 pounds at 100 psi. Four of these will have a capacity of 4,300 pounds so they can handle the 3500 pound…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 8

Since both a ST145/R12 size tire, like the Kenda Karrier S-Trail #AM10130, and a 5.30-12 size tire, like the Kenda K353 #AM10068, fit a 12 inch wheel, a ST145/R12 size tire can replace a 5.30-12 size tire. Keep in mind that these tires do have…

view full answer...

Answer 9

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

Great question, William! The Karrier ST225/75R15 #KE63KV is a KR35 while the Karrier ST225/75R15 #AM10303 is a KR03 according to Kenda. There is a slight variation in the tread pattern and from what Kenda says about them it looks like the KR03 is…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

How To Find Correct 8" Wheel for Taylor-Dunn Hub

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching