Replacement Control Unit For Kwikee Control Unit 9514 On 1993 Fleetwood Southwind

Question

Question:

How can I replace the control box for the kwikee electric steps part # 9514 1993 Fleetwood Southwind

asked by: Allen

0

Expert Reply:

We have exactly what you are looking for.

I reached out to my contact at Lippert who owns Kwikee Steps and based on the 9514 part number on your current control unit you will need the replacement control unit # LC379606.

I included a video of the # LC379606 for you to take a look at.

expert reply by: Samuel C

0

Answer 1

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 4

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 5

It looks like you've got a Kwikee step motor 5973820 and according to my tech contact at Lippert the correct replacement motor is the Lippert Components Kwikee Step Motor Replacement Kit #LC379608. This is a direct replacement for your old unit…

view full answer...

Answer 6

We have exactly the motor you are looking for. If your Kwikee 32 Series Steps were produced between 2000-2005 you will need the Replacement Motor with Mounting Plate for Kwikee Electric RV Steps #LC379608, and if your steps were produced from…

view full answer...

Answer 7

If your RV step's motor is dead (no operation even if you bypass the switches and directly apply 12V power to the motor terminals) then it will require replacement. Your gearbox may still be okay so long as it has not made bad noises when it last…

view full answer...

Answer 8

If the Kwikee 32 Series steps that you have were built in 2003 and you haven't done any work to them then the replacement motor that you are looking for is the part #LC379608. This is for 32 Series steps that were manufactured between 2000 -…

view full answer...

Answer 9

When the 909508000 part number has come up before it has been in relation to Kwikee 40 Series Steps which use the Replacement Control Unit for Kwikee 40 Series Electric RV Steps #LC363985. Unfortunately your motorhome information doesn't actually…

view full answer...

Answer 10

Thanks for the picture! I checked with Progressive Dynamics the replacement power converter you need for your Parallax Series 7300 Model 7345 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp item #PD4645V.

view full answer...

Answer 11

The Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers #PD4645V is exactly what you need for your Magnetek 7300. We have checked with Progressive Dynamics before and this is what they told us is needed. The DC fuse board does not…

view full answer...

Replacement Control Unit For Kwikee Control Unit 9514 On 1993 Fleetwood Southwind

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching