Replacement Hub for AxleTek Hub # BD2-545-17

Question

Question:

Looking to replace brakes and hubs. This looks like the right product. Is this direct replacement for the AxelTeck BD2-545-17?

asked by: Mark

0

Expert Reply:

The exact replacement hub assemblies you need for your BD2-545-17 are the etrailer Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 # AKHD-545-35-K that you referenced.

expert reply by: Jameson C

0

Answer 1

The seal you need for your trailer hub is the #58846. Or for a bearing kit that includes all of the components you'll need you'd want the #BK2-100. For brake assemblies you'd want the part #AKEBRK-35L for the left side or part #AKEBRK-35R…

view full answer...

Answer 2

The Axletek 44-GG is a 10 inch by 2-1/4 inch 3,500 lb axle brake assembly which we offer with the part #AKEBRK-35L-SA.

view full answer...

Answer 3

The exact replacement hub assemblies you need for your BD2-545-17 are the etrailer Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 #AKHD-545-35-K that you referenced.

view full answer...

Answer 4

We don't have a tire in that exact size. We have ones that are close but not quite as wide. They would be about an inch skinnier like the part #AM10130. As long as you have a 12 inch diameter trailer wheel that is 4 inches wide this would work…

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

I have a solution for you but we do not have any standard grease caps with a 2.24" diameter like the #RG04-020 . I recommend going with the Bearing Buddy Bearing Protectors #BB2240 which will not only protect your bearings but provide an easy,…

view full answer...

Answer 7

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Answer 8

There are differences in them but we do have what you are looking for and they can in some situations be used together. The Replacement Trailer Hub Bearing you have part #02475 and Replacement Race for 02475 Bearing part #02420 are designed to work…

view full answer...

Answer 9

The correct set of replacement brake assemblies for your AxleTek 12 inch assemblies is the kit part #AKEBRK-7-SA that you referenced. This kit is a pair of left and right assemblies that are an exact match to what you have that are also self…

view full answer...

Answer 10

Since the system was already working and all of sudden is causing issues for you I suspect that you may be pulling too much solar power for your battery bank causing an overcharge error or a separate system, like your alternator is also charging your…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Hi Ray, the bolt hole spacing for the etrailer Electric Trailer Brakes #AKEBRK-35-SA is 2-7/8" on center, so these sound like they'll work perfect for you.

view full answer...

Replacement Hub for AxleTek Hub # BD2-545-17

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching