Replacement Bunk Brackets for Escort Boat Trailer

Question

Question:

I have a escort trailer as well with same bunk holders. Do you know where I could find replacement ones

asked by: Daniel

0

Expert Reply:

The CE Smith Bolster and Swivel Bracket Assembly part # CE10000G are universal so they can be used in place of pretty much any bunk bracket. If you have angled bunk brackets these would not be an issue because the above bunk brackets can swivel. If you can give me the dimensions of your frame I can then get you the correct u-bolts to use the above bunk brackets.

That said, I would not be able to locate specific bunk brackets so universal options like the above are your best bet.

expert reply by: Conner L

0

Tom

6/28/2024

My escort rail is 4” tall by3” wide. Please advise what u bolts I need

Reply

Bud M.

6/29/2024

@Tom Due to the size of your rail you are going to need to source u-bolts locally as the 3" Long x 4-1/8" # CE15254A we have are not long enough for your rail. You will need to source some at least 3-1/2" long so there is enough threads to secure the bracket.

Reply

Answer 1

The CE Smith Bolster and Swivel Bracket Assembly #CE10000G that you referenced would work well to replace the bunk brackets on your boat trailer. You would be able to set the angle for the bunks that you would like with the #CE10000G also. I attached…

view full answer...

Answer 2

From what I have found, the parts on the sheet you are talking about are no longer around. We do have some available options but they will not be identical to what you currently have. For bunk brackets for your Escort boat trailer, I recommend the CE…

view full answer...

Answer 3

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 4

Hey Fred! If you have an even number of bolt holes you can measure center to center between opposite holes to find the bolt pattern. If you have an odd number of holes you measure from center to the farthest edge. See the attached photo. For example,…

view full answer...

Answer 5

Hey Rebecca! Information is limited and isn't finalized yet from Trailer Valet since the #TV83FR is still a preorder. However, I was able to find that the full height of the jack when it is retracted is 33" from the wheels to the top. I also…

view full answer...

Answer 6

Since your main concern is the marks on the hull of your boat I recommend going to the Yates TPR Ribbed Wobble Roller. These rollers are constructed of thermal-plasticized rubber which is a non-marking, non-scratching material. It is stronger and…

view full answer...

Answer 7

There is not a standard plug available that would allow you to plug the Advent Air Rooftop RV Air Conditioner #ACM135 right to an extension cord. The unit will need to be hardwired using the included wiring and hardware. I have attached the complete…

view full answer...

Answer 8

Thanks for the photos with measurements. The 2-Leaf Slipper Spring w/ Radius End for 1,000-lb Trailer Axles - 24-5/8" Long #SP-177275 are rated for 500lbs each for use with a 1000K axle. This will work with the inside to inside measurement you…

view full answer...

Answer 9

To determine your spindle size, you can either pull one hub off your trailer and look at the bearing numbers on the face of the inner and the outer bearing, or you can measure the spindle itself. I've attached an article and a photo to assist. If…

view full answer...

Answer 10

Thank for the photos of your boat trailer! The CE Smith Double U-Bolt Bolster and Swivel Bracket Assemblies #CE10196G-4 that you referenced are a great option to replace the existing bunk system on your boat trailer. These bolster brackets and swivel…

view full answer...

Answer 11

I have attached a chart you can check out that describes the torque needed per wheel size, wheel stud size and material. For an 8-inch wheel with a 1/2-inch wheel stud the torque is 75 to 86 ft-lbs. For a 15 inch steel wheel with 1/2 inch wheel studs…

view full answer...

Replacement Bunk Brackets for Escort Boat Trailer

Product Page this Question was Asked From

Continue Researching