Where Is The Heating Element Located on Atwood gc6aa-10e Hot Water Heater

Question

Question:

Where is the heating element located on a gc6aa-10e travel trailer hot water heater

asked by: Wayne T

0

Expert Reply:

On your model Atwood Water Heater GC6AA-10E the electric heating element is located in the water tank in the back side of the water heater.

Atwood does recommend having a RV repair shop replace the heating element because of it's location.

expert reply by: Heather A

0

click to enlarge

Answer 1

Hello William, Looks like you already found it. The Progressive Dynamics REL 60A 4500 Series Inteli-Power Converter Section #PD4560CSV is the correct converter for your Progressive Dynamics PD4560K18NS2B. If you plan on making the switch to lithium…

view full answer...

Answer 2

The 6-Leaf Double-Eye Spring #e94SR will work as a replacement for your Dexter 072-097-02 leaf spring. You Dexter spring is the same 26" length as ours but ours will have 6-leaves versus the 4 on your Dexter spring.

view full answer...

Answer 3

I added a photo which shows the location of the heating element of the Atwood Water Heater GC6AA-10E for you. It is item number 17 in the diagram. Atwood does recommend having a professional do the job if you are replacing it due to its location.

view full answer...

Answer 4

The Progressive Dynamics REL 60A 4500 Series Inteli-Power Converter Section #PD4560CSV is designed for lead acid batteries, but a jumper can be installed to make it compatible with lithium as well. Progressive Dynamics has a great step by step…

view full answer...

Answer 5

Yes, you do need to move the jumper over from the lead acid to the lithium setup and you'd have the higher voltage charging profile.

view full answer...

Answer 6

Appreciate the photo, and what that shows is you have a 5,200 lb axle that is 86-1/2 inches hub face to hub face with a spring center to spring center measurement of 68-1/2 inches. We do have a replacement with that capacity and the correct length,…

view full answer...

Answer 7

The length is good on the EZ Flex system #K71-653-00 but the height may be different depending on where you are measuring that 4-3/4 inches. On the EZ Flex the distance from the center of the mounting hole to the center line between the 2 bottom…

view full answer...

Answer 8

The correct replacement water heater element for your model GC6AA-10E Atwood water heater is #AT92249. The element is going to be on the back of your heater. I've attached a diagram to assist because the element is located under a cover. There…

view full answer...

Answer 9

The proper replacement heating element for your Dometic GC6AA-10E is the Camco #CAM02103. Because the element is accessed from the rear of the unit, Dometic recommends having a qualified service center complete the installation. A specific socket is…

view full answer...

Answer 10

That water heater part number you mentioned matches an Atwood that actually doesn't use an anode rod. You'd just need to drain the heater when not in use.

view full answer...

Answer 11

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 12

Hey Bekzod, So while we don't have a way of knowing the exact leaf springs for your Arctic Wolf 5th wheel trailer, I can help you determine the correct replacements. You do have to take a measurement, though it's pretty easy, as all you need…

view full answer...

Where Is The Heating Element Located on Atwood gc6aa-10e Hot Water Heater

Product Page this Question was Asked From

Continue Researching