Voyager Brake Control Wiring Diagram for Installation in a 2005 Chevrolet 1500 Silverado
Published 12/01/2011
Products Featured in This Question
Question:
I have the Tekonsha Voyager Brake Control and want to put it in my 2005 Chevy Silverado 1500. Chevy supplies the z82 glove box jumper, it has 5 wres Dk Blue - Trailer Brake Controller Switched Output Red - Fused Trailer Brake Controller Battery Feed Blk - Brake Controller Ground Lt Blu - Vehicle Stop Lamp Switch to Brake Controller Input BRN - Brake Controller Illumination Could you tell me exactly how to connect the wires from this plug to the Voyager BLK, White, Blue, Red so I know that part of the Installation is correct?
asked by: Howie N
Expert Reply:
The connections you will need to make to install your Voyager brake controller are listed below. If your Voyager has a connector attached to the wires at the back you can use the Pigtail Wiring Harness, # 7894, to connect to the wires on the connector supplied by GM that is similar to the # 3015-S connector we carry. If you wanted a complete harness without splicing you could use the plug-in wiring adapter, # 3015-P. I have added a photo of the connector for the 2005 Chevrolet Silverado with the wiring labeled also.
Dk Blue - Trailer Brake Controller Switched Output - To blue output wire from brake controller
Red - Fused Trailer Brake Controller Battery Feed - To black wire from brake controller.
Blk - Brake Controller Ground - To white wire from brake controller.
Lt Blu - Vehicle Stop Lamp Switch to Brake Controller Input - To red wire from brake controller.
BRN - Brake Controller Illumination - Not used.
I have added a video, see link, showing a brake controller installation on a 2005 Chevrolet Silverado. We also have an FAQ article detailing brake controller installation of the 1999-2006 Chevrolet trucks.
Product Page this Question was Asked From
Tekonsha Voyager Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Splice-In
- Under-Dash Box
- Under-Dash
- Up to 4 Axles
- Indicator Lights
- Single Trailer Only
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Search Results: l44649
- Search Results: tekonsha trailer brake controller
- Search Results: 301500
- Search Results: tekonsha 90195
- Search Results: tekonsha p3
- Search Results: dexter seal 010 019 00
- Article: How to Install a Brake Controller on Chevrolet / GMC 1999-2006 Pickups
- Search Results: brake controller
- Shop: Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Shop: EZ Lube Grease Caps with 2.72" OD - Fits 12" x 2" Dexter 8-Bolt Hubs - Zinc - Qty
- Shop: Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Shop: Tekonsha Prodigy RF Wireless Brake Controller - Trailer Mount w Remote - 1 to 3 Axles - Proportional
- Shop: Trailer Wiring
- Shop: Peterson LED Side Marker and Clearance Light w/ Grommet - Bullet Connectors - Round - Red
- Q&A: What is the Difference Between the Tekonsha Prodigy P2 and the P3 Brake Controllers
- Q&A: Will a Dexter Trailer Hub Fit on a Lippert Trailer Axle
- Q&A: Can I Use Dexter Components on Lippert Axles and Vice Versa?
- Shop: Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles - Qty 2
- Shop: Complete Bearing Kit with L44649 Inner/Outer Bearings and 10-9 Grease Seal Fits 1.063" Spindles
- Q&A: How to Tell if Dexter Axle 3,500 lb Electric Trailer Brakes Will Fit Axle
- Q&A: How to get Power to the 7-Way on a 2004 Chevrolet Pickup for Installation of the Prodigy RF
- Q&A: Is Brake Controller Needed to Stop Trailer with Electric Brakes
- Q&A: Installation Of A Brake Controller On 2012 Volkswagen Touareg
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Article: Troubleshooting Brake Controller Installations