Should I Use Leaf Spring Spacers Lift Blocks on a Trailer to Raise It

Question

Question:

I need to lift this trailer do you have any leaf spring spacer for this Thank you

asked by: Jose

0

Expert Reply:

I do not recommend using a leaf spring spacer (lift block) on your trailer. The reason for this is because they can cause the trailer to become extremely bouncy and rough which is just going to put more stress on your suspension and wear out the trailer faster. Instead, I recommend using an axle flip kit so long as your axle is over the leaf spring pack. If so then you can use part # K71-384-00 if you have a 2-3/8" diameter axle or part # K71-385-00 if you have a 3" diameter axle. This kit will lift the trailer equal to the diameter of the axle and height of the leaf spring pack.

expert reply by: Conner L

0

Rick H.

7/13/2020

Trying to lift a fifth wheel that axles are already below spring from factory. All your articles direct to use the over/under kit but what about axles already below springs. Need about three to four inches of height with new truck. Thanks

Reply

Chris R.

7/17/2020

If your axles are already below the leaf springs, your best option will be to replace your existing hangers with longer ones. This is the most efficient way to raise the trailer. I have attached a link below that will take you to our full selection.

Helpful Links

dept-pg-trailer_leaf_spring_suspension-pt-hangers.aspx

Reply

Thomas B.

9/1/2021

@ChrisR Trying to lower overall height of a 3500 lb cargo trailer. I know smaller wheels is one way. Already have axle over springs. Is there a taller spring seat I could buy to pick up anther inch or so?

Reply

Victoria B.

9/10/2021

@ThomasB I don't know of any taller spring seats to help you lower your trailer, but shorter spring hangers may be an option. Just keep in mind that while changing components like tires you will want to keep your trailer's carrying capacity in mind. If you want to share why you're looking to lower your trailer, I'll see if there's another option that might work for you.

Reply

Answer 1

Hey Denny! We can definitely help you out with that rough ride on your trailer. A pretty standard option is an upgraded equalizer like the MORryde you looked at. The best choice is always going to be the one that matches your current equalizer…

view full answer...

Answer 2

Hey Luis, We can answer both your questions in one as yes, you can change from the CRE3000 to AllTrek 4000, and it's definitely an upgrade worth making, as the AllTrek 4000 is better in a couple ways from the CRE3000. The first is the 4000 is…

view full answer...

Answer 3

In order to choose the correct replacement leaf springs for a trailer you'll need to know the type (double eye/slipper), axle capacity, and unloaded length. The 6-Leaf Double-Eye Spring part #SP-222275 for example measures 24-7/8" long, has…

view full answer...

Answer 4

I do have an upgrade option for your 6-1/16" long, 4" tall Equalizer #TREQ310, and since you don't want to lower the ride height with the E-Z Flex #K71-652-00, I recommend going with an option from MORryde, as the Equa-Flex are just too…

view full answer...

Answer 5

The center bolt of a leaf spring such as #e54SR is essentially structural integrity. The bolt goes through the leafs and helps ensure stability. If you take a look at the photo I've added you can see how the U-bolts and center bolt of the leaf…

view full answer...

Answer 6

I will be happy to explain how to install the shock kit #LC281281. In addition to the instructions below I have also included a picture of the actual instructions. 1. Raise trailer and jack up the axle to release pressure on the springs. 2. Remove…

view full answer...

Answer 7

The bushings for the slipper springs in your Roadmaster Comfort Ride Leaf Spring Suspension Kit w/ Shock Absorbers - Tandem 7K Trailer Axles #RM-2460-2570 would not need grease so you can definitely swap out the wet bolts with some standard bolts…

view full answer...

Answer 8

The Roadmaster Comfort Ride System part #RM-2450 will give you a smoother ride than the Lippert system part #LC281255 that you also mentioned. Our customers prefer the Roadmaster over the Lippert also because of the ease of install too. Some people…

view full answer...

Answer 9

Hey Darrel, we actually have exactly what you are looking for with the part #TRU52FR which is for a 7k axle and is 25-1/4 inch from eye to eye. This is also a 6 leaf spring as well. The spring you referenced would be too short.

view full answer...

Answer 10

It is possible to weld on a brake flange such as Brake Mounting Flange for 1-3/4" Round Trailer Axles - 2K #4-34 for 1-3/4" round axles, but it takes a qualified welder and even then it can be difficult to accomplish. A better solution is…

view full answer...

Answer 11

The best option we could provide you with is the Trailer Idler Axle Beam part #e48GR which measures 60" long and has a 2,000 lb weight capacity. It's not setup for brakes so in order to equip them you'd need to have a brake mounting…

view full answer...

Answer 12

Hey Martin, Yes, I can verify that the 1-3/4 inches that you're seeing from Measurement D is accurate for the 24-7/8" Long 7-Leaf Double-Eye Spring for 8,000-lb Trailer Axles #DX74XR. Just an FYI there is another version of this leaf spring…

view full answer...

Should I Use Leaf Spring Spacers Lift Blocks on a Trailer to Raise It

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching