What Does The Flashing Red Indicator Curt Venturer Trailer Brake Controller Mean?
Published 05/04/2018
Products Featured in This Question
Question:
What would cause an overload and make it go from green bars to flashing red
asked by: Richard D
Expert Reply:
I checked with Curt and you are correct, the flashing red light indicates a brake circuit overload. Since the light is flashing that most likely means you have a short somewhere on the brake output circuit drawing too much power.
To correct this issue, we will need to test the brake controller # C74VV. Sever the brake output wire near the brake controller leaving enough room to reconnect it and then apply the manual slide. Using a circuit tester like part # PTW2993, you should get output to the controller side of the wire you severed.
If these connections check out and the brake controller is properly grounded then its not an issue with the brake controller. If it tests fine then the issue is either a short somewhere that is drawing too much power, or your trailer is actually overloading the controller. More than likely it's a short in the wiring somewhere or the connectors. To find the short, check the connectors, both the vehicle and trailer and inspect the wiring for any damage.
Product Page this Question was Asked From
Curt Venturer NEXT Trailer Brake Controller - Up to 3 Axles - Time Delayed
- Trailer Brake Controller
- Time Delayed Controller
- Electric
- Electric over Hydraulic
- Plug-In
- Under-Dash Box
- Under-Dash
- Up to 3 Axles
- LCD Display
- Single Trailer Only
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Vehicle Tow Bar Wiring
- Shop: Trailer Wiring
- Q&A: Troubleshooting Trailer Wiring Using a 2021 GMC Sierra Truck
- Q&A: Troubleshooting Check Trailer Wiring Message on 2021 GMC Denali Sierra 2500 After Driving
- Shop: 7-Way Trailer Adapter for Towing Trailers with LED Lights
- Shop: Roadmaster Smart Diodes for Variable Voltage LED Tail Lights - Qty 2
- Shop: 7-Way to 4-Way/5-Way Trailer Adapter for Vehicles with Lamp-Out Sensors Towing Trailers with LEDs
- Shop: Trailer Connector Adapter w/ Lamp-Out Sensor Bypass - 7-Way RV to 7-Way RV - Vehicle End
- Q&A: Troubleshooting Venturer Brake Controller Red Light Comes On Intermittently
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Brake Controller
- Q&A: Flashing Red Signal With Curt Venturer Brake Controller
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Hitch
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Video: Finding the Right Trailer Wiring Harness
- Search Results: trailer wiring
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Video: An In-Depth Look at the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit
- Shop: Roadmaster 4-Diode Universal Wiring Kit for Towed Vehicles - 7-Way to 6-Way Coiled Adapter Cord
- Search Results: trailer hitch
- Article: Trailer Wiring Diagrams
- Video: Choosing the Right Tow Bar Wiring
- Shop: Base Plate for Tow Bar
- Q&A: Choosing Between the Brake Buddy Select 3 and the Blue Ox Patriot Supplemental Braking System
- Search Results: base plate for tow bar
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Article: How to Measure for Trailer Hitch Drop
- Search Results: flat tow wiring harness
on Trailer Brake Controller
