Spindle Nut Size For EZ Lube Axles

Question

Question:

What is the spindle nut size in this hub kit?

asked by: Alexander S

0

Expert Reply:

The Trailer Idler Hub Assembly for 3,500-lb E-Z Lube Axles - 5 on 4-1/2 - Galvanized # AKIHUB-545-35-G-EZ-K does not come with the spindle nut. That would come with your axle. For a 3,500 lb axle you would want the Spindle Nut Kit for EZ Lube Axles # RG05-100. The Nut is a 1 inch nut with 14 threads. The socket or wrench needed for this is 1-1/2 inch.

If you just want the nut # 6-191. For the retainer # 6-190.

expert reply by: Jason S

0

Answer 1

EZ Lube axles like the item #T3584F-EZ-8974 come from the factory with just a little bit of grease in the bearings. The first time you use the EZ Lube feature to fill the axle, it will take a lot of grease. You will probably use 3/4 to a full tube…

view full answer...

Answer 2

You can use the Lucas Red "N" Tacky grease with the Easy Grease Trailer Idler Hub Assembly #AKIHUB-545-35-EZ-K. Both of these greases have a lithium complex base formula so they are compatible.

view full answer...

Answer 3

Instead of a castle nut and a cotter pin, your Ez-Lube spindle used a D-washer and a nut retainer. After the bearings are repacked and the grease seal is in place, working the hub gently into place until it seats fully. Install the D-washer then the…

view full answer...

Answer 4

The TruRyde Spindle Nut #165686 has an outer measurement of 1.45 inches. You will use a 1-1/2 inch socket on this castle nut or we usually use a channel lock for these installations. I've attached a video of an installation of a hub to assist.…

view full answer...

Answer 5

In general the amount of articulation travel/play when going from an empty to a maximum load with 12,000 pound Dexter Torflex Axles will be about 2 inches in height and less than an inch in length. I have attached a chart and diagram that goes into…

view full answer...

Answer 6

Yes the Bearing Buddy part #BB1980A-SS is correct for the Dexter hub you have #8-247-50UC3 and then for the bearing kit part #BK2-100 is also correct! You made my job easy.

view full answer...

Answer 7

All of our bearing kits, like the part #BK2-100 that was referenced, only include the inner/outer bearings, grease seal, and cotter pin/washer but I can help you get the other parts that you are needing as well. For 10" x 2-1/4" brakes we…

view full answer...

Answer 8

EZ Lube spindles are generally preferred over Bearing Buddy setups. The EZ lube allows you to insert grease down the middle of the spindle easily which is basically the best option aside from removing the hub and taking it all apart and cleaning and…

view full answer...

Answer 9

Yes you can use a Bearing Buddy on your current axle setup but you'll have to remove the zerk/grease fitting. What you have now is an EZ lube spindle which allows you to push grease through the middle of the spindle but you can install a Bearing…

view full answer...

Answer 10

I reached out to my contact at Dexter and was able to get the wheel bearing numbers you need for your 1999 Jayco Pop-Up Camper. The inner bearing is #L68149 and the outer bearing is #L44649. I recommend getting the complete kit which is Bearing Kit…

view full answer...

Answer 11

When using an EZ-Lube hub, such as hub/drum assembly #AKHD-545-2-EZ-2K, on an EZ-Lube spindle it is not necessary to also use Bearing Buddy bearing protectors. An EZ-Lube spindle, such as part #TRU44FR, has a grease zerk fitting to allow you to pump…

view full answer...

Answer 12

The Hub Bearing Kit for Lippert, Dexter, and Al-Ko Axles #BK2-100 does not come with the grease cap and spindle nut. You will have to purchase them separate. The Grease Cap #RG04-040 has a 1.99 inch outer diameter. The cap has a drive-in…

view full answer...

Spindle Nut Size For EZ Lube Axles

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching