Damper Operation & Installation of Ventline Exterior Wall Vent for RV Range Hoods V2111-55

Question

Question:

Does the vent damper open automatically when we turn on the range hood fan?

asked by: Jim

0

Expert Reply:

Yes, the internal damper in the Ventline Exterior Wall Vents for RV Range Hoods, parts # V2111-55 in black and # V2111-13 in white, opens automatically when you turn on the exhaust fan in your RV's kitchen range hood.

These vents also have a locking feature for the damper that lets you keep it secured in the closed position. Two swiveling latches, one on each end of the damper panel, allow you to secure the damper for off-season storage or when in extreme temperatures when you will want to keep the RV well buttoned up for minimal heat or cooling loss.

Installation requires 10 screws, such as # 31071, as well as a silicone sealant. Silicone rubber sealant is ideal since it both provides a secure installation that resists vibration and rattle, and it blocks entry of rainwater. We offer the sealant in many colors, such as # LT37464 (grey), # LT37467 (black) and # LT37466 (copper).

You can refer to the linked videos for more helpful product information and installation details.

expert reply by: Adam R

0

Answer 1

We do offer a Replacement Damper for Ventline RV Range Hood w/ Horizontal Exhaust #BCA0472-00, which comes in a single piece and has overall dimensions of 9-7/16 inches long x 4-1/2 inches wide. This appears to match the dimensions you are needing…

view full answer...

Answer 2

The Replacement Damper #BCA0472-00 that you referenced is a fit for Ventline P, B, and T Series range hoods so it is compatible with your PR-8 range hood. It does not come with installation instructions as you simply maneuver the damper so that the…

view full answer...

Answer 3

I believe you are referring to the damper like part #BCA0472-00. We do have entire replacement wall vents for range hoods like the 10-1/2" x 3-3/4" Ventline #V2111-13 (which comes with a damper) but we don't have a replacement damper…

view full answer...

Answer 4

If you are just straight up replacing the part with the Replacement Damper #BCA0472-00 then it will perform the same as your old one which means it will probably be making that flapping noise when you're on the highway. Normally there is some way…

view full answer...

Answer 5

The replacement damper isn't available in white, unfortunately. The part measures 9-7/16 by 4-1/2 inches. These vents are usually specific to the brand of the vent hood. The closest thing we offer to what you're looking for would be part…

view full answer...

Answer 6

We have one replacement damper that is pretty close to what you mentioned with the part #BCA0472-00 but this measures 9-7/16" long x 4-1/2" wide so it's about 1 inch less tall than what you mentioned.

view full answer...

Answer 7

The dimensions of the Ventline Replacement Damper for Ventline RV Range Hoods #BCA0472-00 are 9-7/16- long x 4-1/2-inches wide. Based on your photo this replacement part does not appear to be compatible with the size of your vent opening. You may be…

view full answer...

Answer 8

If you are referring to one of the Ventline P, S0721, B, and T Series range hood, the Replacement 12-Volt DC Fan Motor for Ventline RV Range Hood #BVD0218-00-R would not require you to use a resistor or fuse to install it. It sounds like you could be…

view full answer...

Answer 9

Hey Linda, Yep, it sure will; the WeatherTech Roll Up SunShade Kit #WT87QV will indeed fit your 2024 Nexus Viper 27V. This is a good choice as it is double-sided with one reflective side to keep the sun (and heat!) out of your motorhome, with the…

view full answer...

Answer 10

Hey Dave, the wiring that comes with the etrailer RV Solar Panel Kit part #e59FV is 7.5 meters long. I attached a diagram that shows how multiple panels attach to the controller. This is compatible with lithium batteries too. Is this first time with…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Damper Operation & Installation of Ventline Exterior Wall Vent for RV Range Hoods V2111-55

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching