Replacement Brake Shoes And Wheel Cylinders For Mastercraft Boat Trailer

Question

Question:

Hi I have a Mastercraft boat trailer and its model number is PS 205 S. The brake shoes are 10 inches across and 2 1/4 deep. The GVWR is 3740 #s. does not self adjust. can you let me know what part number to get for brake shoe and wheel cylinder assembly?

asked by: [email protected]

0

Expert Reply:

For your Mastercraft Boat Trailer, I recommend the Titan Hydraulic Brake Kit - Free Backing - Galphorite - 10" - Left/Right Hand - 3,750 lbs # T4423500-400. The complete assembly is often less expensive than replacing the individual components. If you want just the components you mentioned, I recommend the 10" X 2-1/4" Hydraulic Brake Shoe/Lining (One Wheel) # BP04-120 and the Wheel Cylinder - 10" and 12" Single Servo RH # BP17-020 in addition to the left hand # BP17-030.

You may also be interested in the Brake Adjustment Spoon for Drum Brakes # W80630 and Mounting Bolts and Hardware for 10" Brake Assemblies # BRKH10A.

expert reply by: Jason S

0

Answer 1

To determine the correct Hub and Rotor for your 2003 Mastercraft single axle boat trailer you will need to determine what the inner and outer bearing part numbers are inside the hub, the brake mounting flange bolt pattern and the correct bolt pattern…

view full answer...

Answer 2

We do have a compatible grease seal for your 168255TC oil seal, however, we do not carry rubber coated seals in this size. The 168255TC oil seal was designed to work with oil bath hubs on a 3,500 lb axle. For the most part, axle manufacturers have…

view full answer...

Answer 3

From my research it appears MasterCraft specifies Kodiak disc brakes on their tandem boat trailers so you'll just want to confirm the axle rating. Then just review the linked page that displays all Kodiak replacement pads like the part #K225CP…

view full answer...

Answer 4

Assuming you are meaning replacing the entire hub, you will first need to remove the oil bath cap to access the spindle nut. There will be a cotter key holding the nut on, or a clip which will need to be removed next. After that remove the nut and…

view full answer...

Answer 5

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 6

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

I do have an option for you but the coupler on your trailer is very old and we simply don't carry parts for them anymore as they were discontinued by the manufacturer. Therefore, the only option we can offer is a new coupler, the Demco Hydraulic…

view full answer...

Answer 10

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 11

First you will need to remove the old hydraulic equipment. Remove the surge coupler or actuator, remove all the lines, and finally remove the brake assemblies. If you have 10 inch diameter hub and drums, you may need to replace those as well. If you…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Replacement Brake Shoes And Wheel Cylinders For Mastercraft Boat Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching