What Size Circuit Breakers Can be Used on a Trailer for Electric Jack and Brake Functions
Updated 06/02/2025 | Published 06/02/2016
Products Featured in This Question
Question:
I have two circuit breakers mounted on my trailer frame near my battery box. They are wired in series output lug of breaker #1 wired to input lug of breaker #2 and each breaker has another wire on the output lug. I assume that one breaker is for the electric brakes and the other is for my electric tongue jack I have not traced the wires yet. The problem is that I need to replace the existing breakers because the housing on both is broken and being held together with a zip tie, but I have no way of telling what size they are. I have looked closely and I do not see any amp rating. The only number visible is on the metal contact plate, inside the breaker between the terminals that has U-21 stamped on it. How can I tell what size they are so I can order replacements?
asked by: Jim
Expert Reply:
If those circuit breakers are indeed for the jack and the trailer brakes then they are likely redundant since the 12 volt circuit and brake circuit are already circuit protected on the vehicle side. Electric trailer jacks also usually have an internal circuit breaker and/or in line fuse. If you want to replace them you can.
If you can verify what they go to as the jack and brakes then jack the specs on the jack to determine its amperage draw. Usually electric jacks on trailers are rated to pull up to 30 amps so you can use a 30 amp circuit breaker # PK54530. For the brakes, since most brake controllers will use either a 20 amp or 30 amp circuit breaker (depending on how many brake assemblies there are) you can just go with another 30 amp breaker.
It is also possible that the circuit breakers were there for some kind of winch. The way you describe it sort of sounds like the circuit breaker sets winches use such as # SW87-22873-16 for example. I anticipate that the mystery of the breaker functions will be solved once you can verify where the wires from them lead.
Product Page this Question was Asked From
In-Line Circuit Breaker - 20 Amp - Perpendicular Mount Bracket
- Accessories and Parts
- Wiring
- Circuit Breaker
- 20 Amp
- Pollak
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Q&A: How To Install a 30 Amp Service on an Enclosed Cargo Trailer
- Shop: RC Manufacturing T-Series Trailer Tongue Tool Box - A-Frame - Aluminum - 2.6 Cu Ft - Silver
- Shop: Brake Controller
- Shop: Progressive Dynamics 4000 Series RV Converter w/ Charge Wizard and AC/DC Distribution Panel - 60 Amp
- Article: Trailer Wiring Diagrams
- Shop: Floor Mats
- Search Results: led strip light
- Shop: Progressive Dynamics REL 60A 4500 Series Inteli-Power Converter Section
- Shop: Bright Way Trailer Breakaway Kit with Charger, LED Tester, and 5 Ah Battery - Side Load
- Shop: Bright Way Trailer Breakaway Kit with Switch and 0.5-Amp Charger
- Video: Progressive Dynamics RV Power Control Center Installation - 2017 Airstream Flying Cloud Travel Trail
- Video: Bright Way Trailer Breakaway Kit with Switch Review
- Q&A: How to Wire 12V Battery in Enclosed Trailer to Power Trailer Lights Independent of 7-Way Connection
- Q&A: Adding a Battery on an Enclosed Trailer to Power Interior Lights
- Q&A: Can I Charge My Trailer Battery Using 7-Way Trailer Connector on Truck
- Search Results: 30 amp breaker box
- Search Results: rv 30amp power cord
- Q&A: Are Propane Tanks Still Accessible with Stromberg Carlson Trailer Tray Cargo Carrier Installed
- Q&A: Will Stromberg Carlson Trailer Tray # CC-255 Fit Lance Trailer with 3 Tank Cover
- Shop: Superwinch S5500 Trailer Winch - Synthetic Rope - Hawse Fairlead - 5,500 lbs
- Shop: Stromberg Carlson Trailer Tray Cargo Carrier for A-Frame Trailers - 300 lbs
- Search Results: redarc liberty
- Search Results: breaker
- Search Results: 110v
- Search Results: weathertech
- Video: Redarc Tow-Pro Liberty Brake Controller Installation - 2013 Toyota Highlander
- Video: Redarc Tow-Pro Liberty Brake Controller Review RED24FR
- Q&A: 30 Amp Circuit Protection for Powered A-Frame Jack
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: What to Know About the Pollak Circuit Breaker
on Accessories and Parts
Markus W.
6/1/2025
I'm looking to eliminate the lead/acid battery from my travel trailer. I purchased a 2600 watt/h li-ion battery that essentially replicates shore power. It runs everything from the slider to the fridge, etc. The issue that I'm running into is with the electric trailer jack (because it is DC). I'm wondering if I can run the wires to my breaker box, install a 30-amp breaker, and then run it off of the battery (or shore power)? Thanks for your time.