Customers compare Y8881250 to these similar products
Products Featured in this Video
Hi there, I'm Michael with etrailer.com. Today we're gonna take a quick look at this Yakima Replacement Hose for your Yakima Road Shower. Now this hose can either act as a direct replacement for the hose that came with your road shower or it can be an add-on hose depending on your needs. This is gonna be compatible with the four gallon or seven gallon Yakima Road Shower. All the model numbers… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…
view full answer...I spoke to my contact at Horizon Global. He said it is acceptable to mount the Bulldog Powered-Drive Kit #BD1824200100 to the slave jack itself. He also said that if you need to switch the motor wires to make it work correctly, that would be fine, as…
view full answer...A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
view full answer...If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…
view full answer...What you are wanting to do is very possible with the GO Power Solar Panel kit part #34273836. You could mount it on your pin box and then run the wiring to your batteries via an SAE connector. We don't have an SAE connector adapter but they are…
view full answer...The typical tire should run about 158 degrees (Farenheidt) once you get going down the road, but this can vary greatly depending on the weight of the trailer, how fast you're traveling, and also driving habits. So while 158 is probably…
view full answer...The Tow Ready wiring harness #118571 is rated for 7.5 amps for brake lights and turn signals and 7.5 amps total for running lights. The fuse that goes on the power wire connection to the battery is a 10 amp fuse. The wire gauge of the long 12 volt…
view full answer...I have spoken with Lippert about the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System part #LC675817 in they past and they informed me that the most important aspect is that the battery/batteries are sufficiently charged, between 12.4…
view full answer...The caliper bracket you are looking for is the Replacement Mounting Bracket #KCMB12D which is compatible with the 5 bolt mounting flange you have as well as the 225 Kodiak Dacromet calipers you have as well. Then for a bolt kit you'd want the…
view full answer...You would not be able to charge your battery through the wiring on your 4-way trailer connector. Since your truck has a 7-way connector, you could maintain the power to the battery but not charge it. To begin, you would need to cut off your 4-way…
view full answer...Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…
view full answer...For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…
view full answer...