Truck Bed Slide Specs:
Features:
Stop crawling into your truck bed to grab your groceries, coolers, and other hard to reach items. Sliding tray extends past the tailgate for easy access to all your gear. Fastens to existing floor board anchor points with no drilling required.
More Information >Truck Bed Slide Specs:
Features:
Stop crawling into your truck bed to grab your groceries, coolers, and other hard to reach items. Sliding tray extends past the tailgate for easy access to all your gear. Fastens to existing floor board anchor points with no drilling required.
More Information >Truck Bed Slide Specs:
Features:
Stop crawling into your truck bed to grab your groceries, coolers, and other hard to reach items. Sliding tray extends past the tailgate for easy access to all your gear. Fastens to existing floor board anchor points with no drilling required.
More Information >Truck Bed Slide Specs:
Features:
...span>4" Tall, extruded aluminum side and cab-end walls help contain cargo Optional add-on segments increase side height to 8" near the cab end of the tray Integrated tie-down tracks on side and...
More Information >Truck Bed Slide Specs:
Features:
...span>4" Tall, extruded aluminum side and cab-end walls help contain cargo Optional add-on segments increase side height to 8" near the cab end of the tray Integrated tie-down tracks on side and...
More Information >Videos
for Truck Bed Slide
Help Articles
for Truck Bed Slide
Expert Answers
for Truck Bed Slide
That spindle looks pretty well destroyed so best option is going to be to replace the axle. You are going to need to measure your current axles in a few places to get the correct one as we don't…
view full answer...I do have an option for you, but we do not carry the Dexter 072-027-00 you mentioned. However we do have the etrailer Double-Eye Spring for 7,000-lb Trailer Axles - 24-7/8" Long #e64SR which will…
view full answer...On a single axle trailer you will want to have a hanger spacing of around 22-3/4 inches when using the 23-1/8 inch long Double-Eye Spring #e59SR. This will allow that rear shackle to correctly lean away from the axle for proper suspension travel.
view full answer...I have spoken with Lippert about the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System part #LC675817 in they past and they informed me that the most important aspect is that the battery/batteries are sufficiently charged, between…
view full answer...The caliper bracket you are looking for is the Replacement Mounting Bracket #KCMB12D which is compatible with the 5 bolt mounting flange you have as well as the 225 Kodiak Dacromet calipers you have as well. Then for a bolt kit…
view full answer...The typical tire should run about 158 degrees (Farenheidt) once you get going down the road, but this can vary greatly depending on the weight of the trailer, how fast you're traveling, and also…
view full answer...I am sorry Lippert did not include their instructions with your Lippert Trailair Air Ride 5th Wheel Pin Box #LC158778 but I have included a link to them on the Lippert website. I also linked an image of page 3 from those instructions which shows…
view full answer...We do have the Rhino-Rack Masterkey Lock Barrels #RRRK093-2 which will provide you with 2 new lock cores and keys for your Rhino-Rack Zenith MasterFit Rooftop Cargo Box #RRRMFZ66. As far as pricing goes on the different sets they can change based…
view full answer...Thanks for the picture of what you have and the info you listed. The correct wheel you need is the part #AM20794 that you referenced.
view full answer...The Bargman 7-Way, RV-Style Connector #WG54006-043 referenced in your question uses the standard RV-style pin locations for its 7-Way connector. I have attached a diagram of these locations and their functions for you to check out. Wire colors will…
view full answer...We do offer the Trailer Connector Adapter, #HM47425, which converts a 7-pole round connector to a 7-pole flat connector. This adapter works for tow vehicles with combined taillight wiring, meaning that the turn signals and brake lights run on the…
view full answer...You can put a maintenance charge on your trailer battery with the 12 volt accessory circuit of the 7-way. The 1:00 position of your 7-way carries this circuit. You would just need to run a length of 10 gauge wire like part #10-1-1 (sold by the…
view full answer...