Salt Spreaders Specs:
Features:
Material packs and jams when spreading from a UTV or short-bed truck. This spreader uses a reversing auger and vibrator to keep it feeding, with a 30 ft spread so you can keep working without stopping to clear clogs on smaller routes.
Installation Notes:
Product fits
Salt Spreaders Specs:
Features:
Material can dump too fast when spreading from an ATV or UTV. This gravity-fed spreader uses an adjustable gate and powered spinner to control output and keep coverage even across trails, property lines, and small areas.
Installation Notes:
Product requires a 2" receiver hitch on the rear of the ATV or UTV.
More Information >Videos
for Salt Spreaders
Help Articles
for Salt Spreaders
Expert Answers
for Salt Spreaders
Hey Mark, the Curt hitch part #C15800 that you referenced is the highest rated hitch we offer for your 2027 Ram 4500. It is rated to tow a trailer up to 20,000 lb with a tongue weight of up to 2,700 lb.
view full answer...Hey Mark, if the lean is due to the weight in your Tiffin not being distributed evenly from left to right then yes air bags would help like with the part #AL88344 for the rear and then #AL88240 for the front. But I would first make sure your…
view full answer...Jorge - you heard right. The Blaster lineup #ME98FR and #ME48FR includes a built-in vibrator to keep material flowing, especially when the salt or ice melt tends to cake or bridge. In wet or semi-frozen material, that vibrator helps prevent clogging…
view full answer...Hey Steve, yes we do! Assuming you don't have the RamBox, the Black Armour Heavy-Duty Truck Bed Mat #BA72AR is what you're looking for. This has a 1/2" thick rubber construction and is custom fit for your Ram 2500. What are you typically…
view full answer...Hey Steven. The measurements you provided are somewhat reasonable. However, I would double check the hub face measurements as the standard 3,500lb axles with 80" spring centers measures 95" from hub face to hub face. The 89" hub…
view full answer...No, it will not Mayra. The Universal Wheel Holder Kit item #HR89FR is designed to replace the wheel holders on the Hollywood Racks Sport Rider SE Bike Rack for 2 Electric Bikes item #HLY84FR. This is a custom fit replacement part so it's not…
view full answer...Hey Jeremy! The SnowBear Snowplow for 2" Hitches #K2AVAL8826 will work well with your 2024 Ram 3500 for your driveway and barn. You won't have any issues reaching the ground well enough to clear. It doesn't look like you have a front…
view full answer...Michelle, great question - the Base Line 240 #ME86FR and 400 #ME26FR handle dry or slightly damp rock salt and calcium blends well, but they’re not ideal for heavy, wet sand or thick mixes. That’s where the Blaster units #ME98FR and #ME48FR shine:…
view full answer...Hey Kevin. The Lippert Replacement Standard Bearing Block Kit item #LC379060 measures 1-11/16" wide. The Replacement Composite Bearing Block Kit item #LC93ED measures 1-9/16" wide. Do you see a white tag located below the motor on the H…
view full answer...The Custom Underbed Installation Kit for B&W Companion 5th Wheel Trailer Hitches #BWGNRK1108-5W is a great gooseneck system and is also a really nice combination with the B&W Companion 5th Wheel Trailer Hitch #BWRVK3500-5W on your 2001 Ford…
view full answer...Hi William, sweet car! The Curt 56146KIT was discontinued a number of years ago, but we have you covered. What you are looking for is the Curt Powered Tail Light Converter w/ 4-Way Flat Trailer Connector and Install Kit #C59496 you were looking at.…
view full answer...Troy, they’re similar but not identical. The #ME26FR Base Line uses the BL electronic controller, which mounts in the cab and gives you On/Off, Faster/Slower, and Vibrate buttons - that last button powers an optional vibrator kit if you add it later.…
view full answer...Filters
- 2 results
Filters
