Result: level

I bought a trailer aid for my rv and it will not pickup the flat off the ground what am I doing wron | The Trailer Aid you have now is similar to our Andersen Rapid Jack part # AM3620 which is used to easily jack up a trailer by rolling a good...

The axles have already been flipped on my trailer and it still sits to low. I was wondering if I can raise it any higher so I can tow it level? Thanks | If your trailer's axles already have an axle over-under kit (also called a flip kit) and...

Springs have already been flipped, I need to raise fifth wheel approx 4” to be level with my Duramax and my pullrite super glide fifth wheel hitch. King pin has already been moved to highest level. How can I get extra height on fifth wheel....

I just bought a new 2014 F250, when I hooked it up to the fifth wheel camper, the back in of the trailer is real close to the ground and i am concerened about damaging my sewer tanks. Do I have any options in raising the back of the trailer?...

Got new truck. 5th wheel does not tow level. There is a 2inch level difference between front and back of trailer 23 feet. Is it okay to tow it as is? I have lowered the truck already. Should I install 2inch lift blocks between Dexter axles and...

I have 2006 take3 51foot wedge trailer with triple 7k axels. Anyway I just upgraded to the 17 ford F350 and i had to raise the front of the hitch up a notch to get it 6inch off the bed. The trailer is no longer riding level. the rear of the...

Hello, my tow vehicle 4x4 Ram sits higher than most trucks so my 5th wheel is not level. The leaf springs are already on top of the trailer axles by manufacture design. Can I simple expend the shackles to get a few inches of height to the rear...

My double axle trailer with eye springs and equalizers has a tall hanger in center position. Can all 3 be the same height? Only 1 needs to be replaced. Since Im going to be this far into repairs I was thinking the higher end hangers would give...

I have a pin box model LIPP 1621 and when towing the trailer it is to high at the hitch as the trailer tilts back, how do I lower it so the trailer tows level. Its a Pullrite super glide so that cannot be lowered. (Jayco Eagle 24.5) and a...

We purchased a 1988 Bee 3 horse goose neck trailer. We then bought 2003 Ford F-350 dually tp pull it. We have found that with 6inch of clearance between truck and trailer, it sits unlovely. 4inch makes it sit better. We currently have 4 225/75-r15...

How much oil do you put in a oil bath axle | Basically you fill up the hub as much as you can through the hole in the cap like the part # RG04-300 and once the oil level is at the bottom of the cap hole it's as full as it needs to be. |

Hi, I bought a used trailer and the brakes are rusty. While disassembling components, the brake actuating level with magnet came off its pivot point. The parts diagram shows that it is removable. What holds it place? | Typically the brake...

On a triple axle trailer with slipper springs the rear equalizer sits at a angle touching the frame and the front equalizer sits level. Should both be the same or is that normal? I double checked hanger spacing and every thing is correct |...

2017 Ram quad-cab, Hemi, big-horn, 4W. Factory Class 4 hitch. Rear of truck very high, and I think I need 6+ inches of to get level with my boat trailer. Worried about the leverage of going to 6,7 or 8 inches of . How much can I employ...

I have see through oil level dexter 21-17 hub caps and looking for replacement. any suggestions ? | I have been unable to find a replacement for a 21-17 Oil Cap (even on Dexter's website), but if you'll use a digital caliper to get the dimension...

I have 2026 F350 DRW l pull a 5th wheel will this effect the on board scale system | Hello John, thanks for reaching out, and congrats on the new truck. Yes, the Timbren Suspension Enhancement System # TFR350SDJ will affect the onboard scales...

I am wondering what grade these u-bolts are manufactured to. Are they comparable to a grade 8 bolt, or closer to grade 5? Thank you. | Thanks for asking Benjamin, I'm sure someone else is wondering the same thing. Redline replacement U-bolts...

Sirs, I need to know why you offer manufacturers spring hanger kits with differing height spring hangers, better stated, I would like to know the science behind offering differing height spring hanger kits. For example, your APT3HD kit has...

What is the thickness of the steel used? Can H-248 come with all six hangers the 3.25inch 28-5 style, or do I need to order six #28-5 to get them all the same size? Thanks, | The thickness of the steel of the Hanger part # 28-5 is 3/16...

Parts are clear allowing visibility of grease level, but no indicator for a FILL LINE. Please advise | Basically you just want to fill the oil, like part # XLPROLUBE, up to where that center plug will fit on the Oil Cap Kit # RG04-300. When...

When I look at the picture of the Correct Track adapter plate and how it bolts up to the existing hanger it doesnt look like mine. My outer hangers are triangular is shape and the adapter plate look like they need to bend over the edges of...

You have two types of flooring bolts: regular black oxide? and ACQ-treated. I realize the ACQ is for pressure-treated wood, but would it also offer better rusting resistance vs. the regular type? | I would recommend to use the treated torx...

Please educate me. Ive got an old camper trailer that Ive stripped down to just the frame. I want it to be a flat bed, but the wheels at rest, are higher than the flat level of the bed. The trailer is currently 30 long, I want it to be 21 long. When...

I am installing a new plywood deck on my snowmobile trailer and the screws I removed are 1-1/2inch long with a head width of close to 3/4. They are self drilling or tapping. The trailer is aluminum and the plywood is 5/8inch thick ccx treated....