LED Strip Lights Specs:
Features:
15-3/4" long x 1" wide x 5/8" thick. Low-profile LED strip light produces bright white light for an interior area. Durable polycarbonate housing and lens. Surface mount - hardware not included. 2-Wire design. 18 Diodes.
More Information >RV Interior Lights Specs:
Features:
Use the integrated switch or wire to a light switch to turn the single dome light on and off. Included incandescent bulb and acrylic lens are perfect for brightening up your RV kitchen when doing dishes or your enclosed trailer when loading gear.
More Information >Videos
for RV Interior Lights
Help Articles
for RV Interior Lights
Expert Answers
for RV Interior Lights
The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you…
view full answer...I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…
view full answer...There should be 2 inches minimum between the tires on a dual axle trailer. This will allow the suspension components room to work properly but a little more room is ideal. For instance the Ultra-Fab Chock and Lock Wheel Stabilizers for Tandem-Axle…
view full answer...Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the…
view full answer...If you look at the brackets of the TorkLift HiddenPower Under-Vehicle Battery Mount #TLA7727 you'll see that the top hook goes much wider than the bottom one. There wouldn't be a frame dimension that…
view full answer...Yes, you will need the Thule universal change key, #853-1251, to remove and install new lock cores. the change key pulls down all the tumblers so the lock can be removed or inserted. The existing lock, if present, will have to be unlocked for the…
view full answer...To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…
view full answer...If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…
view full answer...The first thing to do is disconnect the trailer from the Liberty. Then using a circuit tester, like part #PTW2993, test each pin of the 4-Way. Clip the alligator clip of the circuit tester to the exposed post, the ground wire. Check each pin with…
view full answer...Unfortunately there are no plug-in adapters or harnesses that would allow you to replace the factory 4-way flat trailer connector with a 7-way or a 7-way and 4-way connector on your 2005 Ford F-150. To complete the installation for a brake…
view full answer...The direct replacement for your Atwood Gc6aa/10E water heater has been discontinued. I recommend the Atwood RV Water Heater Item #DMC74FR which only requires a 12-3/4" x 12-3/4" cutout. This is a…
view full answer...The amount of bow that's put into trailer axles like the #7359765 is based on about how much a trailer is typically going to weigh that has a 3,500 lb capacity. So there's a bit of approximation and…
view full answer...