P3 Brake Controller Recommendation for a 2001 Dodge Ram 2500

Question

Question:

My old trailer brake now only works manually and no longer with the brake pedal. It is an old unit and think its time to upgrade. Will the tekonsha 90195 work with my 2001 dodge ram 2500 dodge diesel pick up? Is there any other wiring needed to be included with this controller? It appears the reviews are good on this brake controller and i am willing to give it a shot if it is compatible with my truck. Thank you for the help, sincerely,

asked by: Wilson

0

Expert Reply:

Yes, the Prodigy P3 Brake Controller part # 90195 that you referenced can be installed in your 2001 Dodge Ram 2500. All you would need is the correct install harness to plug into the port under your dash. For that you would want part # 3020-P.

I attached an install video for the install harness for you to check out as well.

In case you wanted to troubleshoot your old brake controller check out the FAQ article I attached on troubleshooting brake controllers.

expert reply by: Jameson C

0

Answer 1

Wow that's an oldie! Controller have come a long way since the Sentinel but it would technically still work if needed. That being said for a trailer that weighs 10,000 lbs I would strongly recommend you go with a proportional brake controller…

view full answer...

Answer 2

I spoke to my contact at Tekonsha and they said the LCD display on the Tekonsha Prodigy P3 Trailer Brake Controller part #90195 is part of the limited lifetime warranty. Therefore, if you have an issue with the screen bleeding in from the sides then…

view full answer...

Answer 3

Yes, you can install the Hayes G2 Brake Boss Trailer Brake Controller w/ Mounting Sleeve #HA81792BB in your 2011 Jeep Grand Cherokee. The connector should be mounted on top of the emergency brake bracket, it's gray in color. Once you find it all…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

P3 Brake Controller Recommendation for a 2001 Dodge Ram 2500

Featured Help Information

Miscellaneous Media

Continue Researching