Installation Instructions for Dexter Trailer Springs Over-Under Conversion Kit # K71-384-00

Question

Question:

I have one of your kits enroute, and wanted to see install process before it arrived, thanks

asked by: Jeff D

1

Helpful Expert Reply:

Thank you again for ordering with etrailer.com, we appreciate your business.

I have attached a scan of the installation instructions for the Dexter Trailer Springs Over-Under Conversion Kit, # K71-384-00.

expert reply by: Leah S

1

click to enlarge

Answer 1

As long as the axle on your trailer features a 2-3/8 inch diameter the Dexter Over-Under Conversion Kit #K71-384-00 referenced in your question will work perfectly to gain more clearance on your trailer. The kit will raise the trailer by the height…

view full answer...

Answer 2

If you measure just the width of your toy hauler's rear door opening I can determine which LaSalle Bristol CrossBreeze Screen you'd need. The part #3441409775PBK that you referenced is the correct screen if your opening is 97-3/4 inches wide.…

view full answer...

Answer 3

I attached a picture that shows how the SolidStep Manual Fold-Down Steps #LC791572 would fit over a taller threshold like you mentioned. I also attached a review video for this for you to check out too.

view full answer...

Answer 4

90-120 ft lbs of torque is probably about right for your 15 inch trailer rims. If you check out the lug nut torque chart that I attached you will see that nearly all of the torque specs are that and higher. You'll need to know the diameter of the…

view full answer...

Answer 5

There are two ways to wire up two batteries. One way doubles the volts of the two batteries and the other keeps the same amount of volts. In parallel the voltage stays the same and in series it is doubled. Check out the diagram for more info.

view full answer...

Answer 6

Hey Richard, great question. To get the full 2-1/4" lift on a tandem axle setup, you actually need the triple axle kit part #RR55QX instead of the #RR23QX tandem axle kit. You could also achieve this by getting the tandem axle kit, and an…

view full answer...

Answer 7

It's not a stupid question, it's a perfectly logical one but you should not flip the Dexter Trailer Axle Beam with 4" Drop E-Z Lube Spindles #7685269 to get rise as this was not the intended design as it is an underslung axle with spring…

view full answer...

Answer 8

Hi Brent! You have decided upon the easiest and quickest way to lift your trailer, and for that, I commend you. The only thing we need to know to get you the correct Over-Under Kit is the diameter of you axle. I have both options listed below:…

view full answer...

Answer 9

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 10

Hi John, That sounds really cool! Let me see if I can help you make that vision come true. The patio kit you mentioned, part #LC27FR, is actually the only full "patio kit" we carry — but I’m afraid it might be a little too wide for your…

view full answer...

Answer 11

I do have all of the components you will need to flip the axle on your tent trailer but there is not an all inclusive kit per se to do so. However, the kits are pretty basic as all they include are u-bolts, tie plates, and spring seats. For your…

view full answer...

Answer 12

The best option to lift your trailer with 3,500 lbs axles is definitely going to be the Dexter Trailer Springs Over-Under Conversion Kit #K71-384-00. The reason for that is it is going to give you the most clearance, because it moves your…

view full answer...

Installation Instructions for Dexter Trailer Springs Over-Under Conversion Kit # K71-384-00

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching