Replacement Amber Beehive Light Recommendation for a Yakima Rack and Roll Trailer

Question

Question:

The beehive lamps on my Yakima trailer are not LED but tungsten. What replacement module can I use to replace a broken beehive running light the amber lights?

asked by: Bruce

0

Expert Reply:

The correct replacement amber beehive light you would need for your Yakima Rack and Roll Trailer part # Y08106 that you referenced would be the # Y8880187.

expert reply by: Jameson C

0

Need B.

7/6/2026

I need the replacement “beehive” lights for the rack and roll trailer. Can you carry the part or advise on a suitable substitute. Thanks

Jameson C.

7/6/2026

@NeedB I wish we could still get them but they haven't been available since 2023.

Need B.

7/7/2026

@JamesonC - - they still make the trailer. Are you sure there isn't a part? I think there is

Jameson C.

7/7/2026

@NeedB I wish we could get it. It doesn't make sense that it's not available but I checked with yakima and the behive light and bracket it only part they don't have active right now. The yak part number was 8880187 though so maybe you can find it somewhere else online.

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 6

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

Congratulations on the new Redarc Tow-Pro Liberty part #RED52VR Brian! You picked a great brake controller. Since your 2017 Subaru Outback doesn't have the factory tow package, I'm assuming you're starting from scratch with the trailer…

view full answer...

Answer 11

Hey Adrian, you are on the right track for a hitch for your 2017 Subaru Outback Wagon. I would recommend the Curt part #C13410 as it has plenty of towing capacity, is mostly hidden, and the advantage it has over the Draw Tite is that we just have…

view full answer...

Answer 12

The trailer hitch with the best receiver depth, or bumper clearance, for your 2019 Subaru Outback is the Draw-Tite Trailer Hitch #76227 which is about 2 inches from the hitch pin hole to the edge of the bumper. This is an inch more clearance than the…

view full answer...

Replacement Amber Beehive Light Recommendation for a Yakima Rack and Roll Trailer

Continue Researching