Replacement Bushings for # TREQ310 Trailer Suspension Equalizer

Question

Question:

Last year I purchased 2-EQ310 equalizers and 2 wet bolts. I have used my trailer 25foot 5er less than 5000 miles and have severe wear on right rear tire. I took my trailer to a RV repair shop and they say that the bushings are gone in the R H equalizer. Do you have replacement bushings?

asked by: Larry D

0

Expert Reply:

According to Tru-Ryde, the actual hole in your # TREQ310 equalizer should be 11/16 with the inside diameter of the bushing to be 9/16 of an inch. If this is the case, you'd need the # TRBU11566 bushing.

expert reply by: Mike L

0

Answer 1

You are going to want either our Bearing Kit #BK2-100 or the Timken Kit #TMK52VR. Both of these kits will give you the inner/outer bearings and races along with a grease seal and cotter pin/D-washer for one hub. You always want to replace the race…

view full answer...

Answer 2

The overall diameter of your tire size 205/75-15 is 27-1/4 inches so a cover set like the part #290-3953 would work great as it fits tire diameters that are between 27 and 29 inch. This cover gives you two tire covers that are made from a long…

view full answer...

Answer 3

I recommend the Adco Ultra Tyre Gard tire covers, part #290-3973 in black or #290-3953 in white. Your 205/75-15 size tire is just over 27 inches in diameter so these will fit nicely. These will do a great job protecting your tires from the elements…

view full answer...

Answer 4

I definitely understand how safety chain capacities and determining exactly what chain rating you need for your trailer can be a bit confusing. To keep it as simple as possible, safety chain requirements state that the breaking strength of EACH…

view full answer...

Answer 5

As with any other item on a trailer, such as tires, wheels, winches or jacks, when selecting safety chains you want to ensure a good safety margin, in other words, you want to use an item that has a good bit more capacity than you will actually need.…

view full answer...

Answer 6

Your 13-10 equalizers, which should be equivalent to Equalizer #TREQ310 measures 6-1/16 inches from bolt hole to bolt hole (see accompanying photo) and due to that you will need to use the E-Z Flex Heavy Duty Rubber Suspension System #K71-652-00.…

view full answer...

Answer 7

I understand your worry Tom, and I have a couple recommendations. First is the MORryde ALLTREK 4000 Shock Absorbing Equalizers #MR89DR which has a height of 4-1/2" for the mounting bolts. This is also 6-1/2" in width like the shorter…

view full answer...

Answer 8

The 3" Round Trailer U-Bolts #SP01-080 are the longest we carry at 7-1/4" long with a diameter of 9/16". You will need to source the longer bolts from a local hardware or auto parts store.

view full answer...

Answer 9

The correct replacement for a Dexter 13-10 Equalizer is the Triangular Equalizer part #TREQ310, not the Curved Equalizer part #TREQE1. If you want to upgrade, the Equa-Flex Cushioned Equalizers part #LC279688 would work but you might want to go with…

view full answer...

Answer 10

Hey Jeff, since you have a Bulldog powered 4k trailer jack part #BD500199 the correct replacement manual override rubber plug would be the part #BD500201.

view full answer...

Answer 11

The equalizers that come with the Dexter Heavy-Duty Suspension Kit #K71-448-00 have bolt holes that measure 6" apart on center and then 4" tall on center as you can see in the attached photo. You'll want to measure your current…

view full answer...

Answer 12

Hi Hans, We can get your Keystone trailer set up with new leaf springs, bushings, and wet bolts. Thanks for the measurements and let's start with the leaf springs; for 26 inch eye-to-eye springs what you can use is the 4-Leaf Double-Eye Spring…

view full answer...

Replacement Bushings for # TREQ310 Trailer Suspension Equalizer

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching