Cruise Control Stopped Working after Tekonsha P3 Installation
Updated 03/28/2024 | Published 08/17/2014 >
Question:
Hello, I installed the P3 on a 2010 Toyota Sienna. I double and triple checked the wiring and everything is OK. The problem is now the Cruise Control doesnt work. The Cruise Control light stays on steady as it should when I turn it on at the same time the brakes are applied, and will stay on steady as long as the brakes are applied. But as soon as I release the brakes the Cruse Control light blinks and wont work. This is without a trailer connected. Ive tried everything I can think of. Any help would be greatly appreciated. Oh and by the way the trailer brakes seems to be working fine when using the P3 and the P3 doesnt give any errors when pulling the trailer. So Im fairly sure everything is hooked up properly. The only issue is the Cruise Control doesnt work!
asked by: Tim W
Expert Reply:
We have seen this issue before and when cruise control functionality gets affected after a brake controller install the problem is the stoplight switch wire that was used for the installation of the brake controller.
Basically the red wire of the Prodigy P3 Brake Controller # 90195 that you referenced isn't installed on the correct circuit. You want to find the circuit on your brake switch that only sees voltage when the brakes are applied.
I attached an FAQ on brake controller installation from scratch that you may find helpful.
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Brake Controller
- Video: A Closer Look at the Hollywood Racks Sport Rider SE Bike Rack
- Search Results: curt triflex
- Search Results: etbc7 wiring kit
- Q&A: Why Would Prodigy P3 Brake Controller Show Varying Voltage at all Times As Output
- Q&A: How To Test A Prodigy P3 Controller Without Having Direct Access To The Trailer
- Q&A: Installing Tekonsha Prodigy P3 Brake Controller on 2016 Chevy Silverado with Tow Package
- Shop: Curt TriFlex NEXT Trailer Brake Controller w/ Plug-In Harness - 1 to 4 Axles - Proportional
- Search Results: trailer hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer tires and wheels
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Shop: Trailer Wiring
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Article: How to Measure for Trailer Hitch Drop
- Video: Redarc Tow-Pro Liberty Brake Controller Review RED24FR
- Search Results: trailer wiring
- Q&A: Parts Needed to Install a Red Arc Brake Controller in a 2023 Toyota Tacoma
- Shop: Suspension Enhancement
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Video: An In-Depth Look at the Roadmaster Battery Charge Line Kit for Towed Vehicles
- Q&A: What Gauge Wire Should be Used to Wire Trailer Brakes
- Search Results: trailer jack
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Base Plate for Tow Bar
- Shop: Redarc Tow-Pro Liberty Brake Controller w/ Universal Wiring Harness - Dash Knob - Proportional

Steve
3/24/2024
The harness purchased for 2008 tundra for P3 worked 2 years until it gradually ruined my cruise. I replaced cruise control but the issues with telonsha persist.