Why Would Prodigy P3 Brake Controller Show Varying Voltage at all Times As Output
Updated 05/25/2025 | Published 04/08/2025 >
Question:
I installed a Tekonsha Prodigy P3 Trailer Brake Controller with proportional breaking late last year and noticed that the proportional breaking may not be working correctly. The amount of brake applied while slowing is inconsistent and bounces around. In the troubleshooting menu, all looks normal except for the Output voltage. It bounces around as well, even when sitting completely still. It is mounted straight with the truck. If I tilt it up and down the output bolts jolt around but still inconsistently. Looking for any ideas, or perhaps whether I could have ended up with a faulty unit.
asked by: Austin
Expert Reply:
Hey Austin, it sounds like your P3 part # 90195 has a short from the 12 volt power wire (black) to the stoplight switch (red) and the brake controller thinks that you are applying the brakes and is activating the controller which is making it think it needs to search for braking action. I would go over the red and black wire of the brake controller and see if you can find any cut or exposed wire and insulate as needed with electrical tape.
Continue Researching
- Shop: Brake Controller
- Video: Review of TruRyde Trailer Suspension Parts - Center Hanger For Equalizer - TRHG291-C
- Search Results: etbc7 wiring kit
- Search Results: curt echo brake controller
- Search Results: prodigy p2 brake controller
- Shop: Bright Way Trailer Breakaway Kit with Charger, LED Tester, and 5 Ah Battery - Side Load
- Shop: Curt TriFlex NEXT Trailer Brake Controller - 1 to 4 Axles - Proportional
- Shop: Square Trailer Jack w/ Handle - Side Pin Drop Leg w/ Spring - 12-1/4" Lift - 10,000 lbs
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Search Results: hanger
- Search Results: equalizer
- Search Results: drum hub
- Search Results: tekonsha 90195 p3 electronic brake control
- Shop: Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 - Pre-Greased
- Shop: Curt TriFlex NEXT Trailer Brake Controller w/ Plug-In Harness - 1 to 4 Axles - Proportional
- Shop: Pre-Drilled Round Rubber Trailer Bumper - 96" Long x 3" Wide
- Video: A Closer Look at the Hollywood Racks Sport Rider SE Bike Rack
- Q&A: How To Test A Prodigy P3 Controller Without Having Direct Access To The Trailer
- Q&A: Installing Tekonsha Prodigy P3 Brake Controller on 2016 Chevy Silverado with Tow Package
- Q&A: Cruise Control Stopped Working after Tekonsha P3 Installation
- Article: Brake Controller Installation: Starting from Scratch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Video: Redarc Tow-Pro Liberty Brake Controller Review RED24FR
- Shop: Trailer Wiring
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Parts Needed to Install a Red Arc Brake Controller in a 2023 Toyota Tacoma
Austin
4/9/2025
Hi there! Thanks for the reply. This is actually only occurring WHILE I’m pressing the brakes. Without the brake pedal pressed it is a constant 0.0 volts. Once brakes are applied, the voltage starts around .8, then jumps to 1.6 and up and down from there. If I angle the unit up and down to simulated proportion, the output power jumps sporadically in whatever direction I’m angling it. If I angle it up, the output power jumps high. If I angle it down it jumps in the lower range but the changes are never fluid, always bouncing around. When I’ve performed any of these tests, it is always while the brakes are pressed.