Length of the Pins in the Shoe Hold Down Spring part # BP06-120

Question

Question:

Hi would you tell me the length of this pin, I am looking for one that is 2inch long thanks Greg

asked by: Greg B

0

Expert Reply:

I went out into our warehouse and measured the pin of the Shoe Hold Down Spring part # BP06-120 and found that it measured 3 inches.

expert reply by: Jameson C

0

Answer 1

The 10" x 1-1/2" braking assemblies part #K23-472-473-00 will use the same four bolt brake mounting flange as the 10" x 1-3/4" braking assemblies you have but the hub/drum that goes with these uses a LM67048 inner bearing and…

view full answer...

Answer 2

The process is essentially the same as manual adjust brakes but is just a bit more challenging because self-adjusting brakes, like the Electric Trailer Brake Assembly #AKEBRK-35L-SA, don't give you any room to work. You would need to lift the…

view full answer...

Answer 3

Yes, the Dexter Electric Trailer Brake Kit part #23-26-27 will fit AL-KO Axles. They use the same four bolt pattern as Dexter does for the 3,500 lb model so there will be no issues.

view full answer...

Answer 4

It sounds like you are talking about the parts that hold the brake shoes down. These parts include hold down springs that have little caps on them through which the hold down pins are inserted. We have kit #AKBRKR-SHD which will work with AxleTek,…

view full answer...

Answer 5

The flange on the MaxxFan Deluxe Roof Vent #MA00-06200K you referenced measures 16-1/2" long x 16-1/2" wide. If your current flange has this same measurement then you could possibly just place it on your existing flange but there really is…

view full answer...

Answer 6

To determine your current opening size you will want to measure the rough opening on your trailers' roof. Make sure to remove the garnish ring in your roof's opening to get an accurate measurement. The most common openings is 14 1/4" x…

view full answer...

Answer 7

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Answer 8

Based on information I was able to find online it looks like your Meher 3,750lb axle uses the same Bearing Kit #BK2-100 as a standard 3,500lb axle. Depending on your exact bolt pattern it may be better to carry a spare Hub #CE13511 as this is much…

view full answer...

Answer 9

If your brake shoes#bp04-065 are 10" x 1-1/2" you will need these brake springs #K71-362-00. The springs you were looking at #BP06-120 were for 2-1/4" shoe width.

view full answer...

Answer 10

To determine the correct brake kit you'll need to measure the diameter of the brake pads (from one side of the assembly to the other). If it is 10" and you have hydraulic brakes then I recommend the Titan Free Backing Kit #T4071600-500, but…

view full answer...

Answer 11

There is a quality difference between the Taskmaster Provider tire #TTWTRTM2358016E and the Taskmaster Contender, #C23516E. The biggest difference is in the tread. The Provider just has better tread. The Contender was meant as a less expensive radial…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Length of the Pins in the Shoe Hold Down Spring part # BP06-120

Product Page this Question was Asked From

Continue Researching