Replacement Bearing Kit For a Meher 3,750lb Trailer Axle

Question

Question:

I like to carry extra bearings on road trips for my trailers. I bought a 2023 boat and it has a Meher 3750 pound axle. I contacted to manufacturer but no answer. I would like a spare set of bearings and seals. Any idea other that ripping it apart and getting the numbers ..? Thanks

asked by: David S

0

Expert Reply:

Based on information I was able to find online it looks like your Meher 3,750lb axle uses the same Bearing Kit # BK2-100 as a standard 3,500lb axle. Depending on your exact bolt pattern it may be better to carry a spare Hub # CE13511 as this is much easier to put on in a roadside breakdown. This particular hub has the commonly found 5 on 4-1/2" bolt pattern.

expert reply by: Bud M

0

Answer 1

Yes, the now discontinued Draw-Tite 5th wheel slider hitch 6033 can be used in your 2011 GMC Sierra 2500 short bed. You will just need an installation kit for the truck. You have some options for an installation kit. You can use a universal kit,…

view full answer...

Answer 2

There is a quality difference between the Taskmaster Provider tire #TTWTRTM2358016E and the Taskmaster Contender, #C23516E. The biggest difference is in the tread. The Provider just has better tread. The Contender was meant as a less expensive radial…

view full answer...

Answer 3

To determine the correct brake kit you'll need to measure the diameter of the brake pads (from one side of the assembly to the other). If it is 10" and you have hydraulic brakes then I recommend the Titan Free Backing Kit #T4071600-500, but…

view full answer...

Answer 4

I went out into our warehouse and measured the pin of the Shoe Hold Down Spring part #BP06-120 and found that it measured 3 inches.

view full answer...

Answer 5

If your brake shoes#bp04-065 are 10" x 1-1/2" you will need these brake springs #K71-362-00. The springs you were looking at #BP06-120 were for 2-1/4" shoe width.

view full answer...

Answer 6

For a Lippert 4,400 lb trailer axle the correct bearing kit is the part #BK2-100 which includes inner bearing #L68149, inner race #L68111, outer bearing #L44649, outer race #L44610, grease seal #58846, a cotter pin and a tang washer.

view full answer...

Answer 7

Hey Shane, so the Timken bearing kits are made in the USA so what would be perfect for you would be the part #TMK52VR is a USA made 3,500 lb axle trailer bearing kit. Have you had bearing problems in past?

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

Hey Travis, the Lippert 4,400 lb axles use the same bearings and seals as a Lippert 3,500 lb axle so you can use the Bearing Kit for #84 Spindle part #BK2-100 for a kit that includes the correct bearings and seal. Are you doing yearly maintenance or…

view full answer...

Answer 10

Hey Greg, There unfortunately there isn't a guide to tell us the bearing and grease seal combination for your hub so you'll have to remove it and check the bearings/seal for their part numbers or use a digital caliper #PTW80157 to measure the…

view full answer...

Answer 11

I believe you meant a TDE 46245, is that correct? If that's the case, you've got a 3500 lb axle which uses a 10 inch hub/rotor with a 5 on 4-1/2 wheel bolt pattern. You'll want to use the Kodiak #KHR10D hub/rotor as a replacement. The hub…

view full answer...

Answer 12

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Replacement Bearing Kit For a Meher 3,750lb Trailer Axle

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching