Replacement Hold Down Springs and Pins for Electric Trailer Brakes

Question

Question:

Could you please tell me what spring bushings and spring sidebars are in my tralers electrical braking system. Cant find them anywhere. Thank you

asked by: Marie

0

Expert Reply:

It sounds like you are talking about the parts that hold the brake shoes down. These parts include hold down springs that have little caps on them through which the hold down pins are inserted.

We have kit # AKBRKR-SHD which will work with AxleTek, Dexter, Lippert (LCI), IAC, and AL-KO 10 or 12 inch brakes with shoed widths of 2 inches or 2-1/4 inches.

If you have different size brakes or you are talking about different parts let me know.

expert reply by: Michael H

0

Answer 1

The 10" x 1-1/2" braking assemblies part #K23-472-473-00 will use the same four bolt brake mounting flange as the 10" x 1-3/4" braking assemblies you have but the hub/drum that goes with these uses a LM67048 inner bearing and…

view full answer...

Answer 2

The process is essentially the same as manual adjust brakes but is just a bit more challenging because self-adjusting brakes, like the Electric Trailer Brake Assembly #AKEBRK-35L-SA, don't give you any room to work. You would need to lift the…

view full answer...

Answer 3

Yes, the Dexter Electric Trailer Brake Kit part #23-26-27 will fit AL-KO Axles. They use the same four bolt pattern as Dexter does for the 3,500 lb model so there will be no issues.

view full answer...

Answer 4

I went out into our warehouse and measured the pin of the Shoe Hold Down Spring part #BP06-120 and found that it measured 3 inches.

view full answer...

Answer 5

The flange on the MaxxFan Deluxe Roof Vent #MA00-06200K you referenced measures 16-1/2" long x 16-1/2" wide. If your current flange has this same measurement then you could possibly just place it on your existing flange but there really is…

view full answer...

Answer 6

To determine your current opening size you will want to measure the rough opening on your trailers' roof. Make sure to remove the garnish ring in your roof's opening to get an accurate measurement. The most common openings is 14 1/4" x…

view full answer...

Answer 7

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Replacement Hold Down Springs and Pins for Electric Trailer Brakes

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching