Will the Dust Cap Driver Tool part # 290-992 Work On EZ Lube Spindles

Question

Question:

Will the dust cap driver -Dust Cap Driver Tool - Medium - for 2.440inch OD Grease Caps - fit over the dust caps for EZ Lube axles with the rubber plug, or just the solid caps? Thanks

asked by: Victor

0

Expert Reply:

As long as the dust cap on your hub has a 2.44 inch outer diameter the Dust Cap Driver Tool part # 290-992 that you referenced would work for your cap regardless if it is for a EZ lube spindle or non-EZ lube spindle.

I attached a review video for you to check out as well.

expert reply by: Jameson C

0

Answer 1

I checked with Aliner for availability of key number SM103 and and they do still have some keys for that lock. You can contact them directly for a replacement key. I sent their phone contact information to you. If you ever decide to replace the whole…

view full answer...

Answer 2

For the TruRyde Lubed Dust Cap and Rubber Plug #DC250L-DCRP referenced in your question, which has dimensions of 2.45 inch x 1.52 inch x 1.18 inch, you can use the Redline Dust Cap Driver Tool - Medium #290-992. This can be used for installation,…

view full answer...

Answer 3

EZ Lube Dust Caps, like #DC200L-DCRP, have a rubber plug that can be removed to access the zerk fitting. The rubber plug can be removed by gently prying it up with a flathead screwdriver. If your dust cap is in good condition and you want to avoid…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Will the Dust Cap Driver Tool part # 290-992 Work On EZ Lube Spindles

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching