Replacement Equalizers for a Dexter 13-122 Equalizer
Updated 09/27/2026 | Published 09/25/2026 >
Products Featured in This Question
Question:
I am considering either the Morryde CRE3000 MR27ZR or the AllTrek MR29DR for my Alliance ML226. Do you know if using the AllTrek equalizer would raise the height of the trailer? Thx much
asked by: Michael S
Expert Reply:
Welcome back Michael. The MORryde AllTrek 4000 Equalizers # MR29DR will not add any height to the suspension of your Alliance ML226 trailer. These are designed to keep you at stock height and smooth out the ride.
The best way to chose a replacement equalizer is to match up the dimension of the ones currently on your trailer so you don't through off the geometry of your suspension.
The MORryde AllTrek 4000 Equalizers # MR29DR are 8" wide from the center of the left and right mounting holes and from the top mounting hole to the center line of the left and right mounting holes is 4-3/8".
The MORryde Shock Absorbing Suspension Equalizers item # MR27ZR are 8" wide and from the top mounting hole to the center line of the side mounting holes is 3-1/2".
I attached a couple of diagrams below so you can see the dimensions I listed above.
I recommend measuring your Alliance's equalizers and choosing the one that matches the dimensions of it the closest. If you would like me to recommend a different equalizer I would just need the measurements I provided of the two MORryde options you were looking at.
Are you looking to increase the height of your Alliance trailer or is that something you're trying to avoid? Feel free to answer this and throw in any other questions you have, where it says Add Comment.
Product Page this Question was Asked From
MORryde AllTrek 4000 Equalizers for Tandem Axle Trailers - 35" Wheelbase
- Trailer Suspension Parts
- Equalizer Upgrade Kit
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Double Eye Springs
- Tandem Axle
- MORryde
more information >
Featured Help Information
Instructions
Continue Researching
- Search Results: u012~016
- Shop: Lippert Road Armor Shock-Absorbing Equalizer Kit - Tandem Axle - 3,500-8,000 lbs
- Q&A: Will 3-1/8 Inch Shackles Cause Suspension Geometry Issues With Road Armor Equalizers?
- Search Results: smart plug
- Search Results: smartplug 30 amp
- Shop: MORryde Shock Absorbing Suspension Equalizers for Tandem Axle Trailers w/ 35" Wheelbase - 8K
- Shop: MORryde AllTrek 4000 Equalizers for Tandem Axle Trailers - 35" Wheelbase
- Q&A: Looking for the Suspension Equalizer Upgrade Kit for a 2023 StarCraft Autumn Ridge FBS
- Q&A: Upgraded Equalizers for Tandem Axle Trailer With Dexter 13-122
- Q&A: Recommendation for upgrading equalizer on the Alliance delta Ultralight ML226
- Q&A: Does It Matter If Blue or Yellow Road Armor Equalizers Are Used?
- Shop: Equa-Flex Cushioned Equalizers - Double Eye Springs - Tandem Axle - 5K to 8K - Greasable Pivot
- Shop: Air Distribution Box - Furrion Chill Cube Variable Speed Low Profile AC - 13.5K/15K - R32
- Q&A: Can E-Z Flex Rubber Suspension System Work w/ Wide Trax Trailer Suspension
- Shop: Dexter E-Z Flex Suspension Kit - Double-Eye Springs - Tandem Axle - 6,000 lbs
- Shop: Equa-Flex Cushioned Equalizers - Double Eye Springs - Tandem Axle - 4K to 6K
- Q&A: Will Road Armor Shock Absorbing Equalizer Kit Work with a 35" Axle Spread
- Search Results: trailer hitch
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Search Results: trailer tires and wheels
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Suspension Enhancement
- Search Results: trailer wiring
- Article: How to Accurately Measure Trailer Leaf Springs
- Video: A Look at the Power Mountain Tallboy 6 Ton Off-Road Bottle Jack with a Military Cargo Trailer
- Search Results: trailer jack
- Article: How to Measure Your Trailer Wheel Bolt Pattern




Michael S.
9/26/2026
Jerred, Thanks for the quick reply! The existing equalizer is a Dexter 13-122 (left to right mounting holes center line is 7 3/4") (center top to bottom mounting holes centerline is 2 3/4"). Taking in the consideration of the rubber dampeners compression, I think the CRE3000 MR27ZR would not change the height much if any. However, it does look like the AllTrek MR29DR may add 1 1/2" - 2" of height. My trailer sits a little nose high when on the ball of my truck, so raising it would be a good thing. Plus, the increased travel of the AllTrek is a plus. I went thru both Morryde Qualification Guides and both are good. Am I missing anything a novice like me hasn't thought of? Your thoughts. Thx again