Recommended Amber and Red Marker Lights w/a Grommet for a 3" Diameter Hole

Question

Question:

I have a 3 inch hole looking for marker lights red and yellow to fit with rubber seal

asked by: Jeff H

0

Expert Reply:

Thanks for the information Jeff and welcome back! For amber and red marker lights that fit in a 3" diameter hole with a rubber grommet, I recommend the following parts:

item # MCL59RB - Side Marker with Reflector - Red - 2.5" Diameter

item # MCL59AB - Side Marker with Reflector - Amber - 2.5" Diameter

item # A46PB - Right Angle 2-Wire Pigtail for Trailer Lights - You'll need one for each of the marker lights.

item # A55GB - Rubber Grommet for 2-1/2" Round Trailer Lights - Fits a 3" diameter hole. You'll also need one for each marker light.

What kind of trailer or work truck bed are you replacing the marker lights on and how many are you needing of each color? Feel free to answer this and throw in any other questions you have, where it says Add Comment.

expert reply by: Jerred H

0

MCL59RB
(click to enlarge)

MCL59AB
(click to enlarge)

A55GB
(click to enlarge)

Answer 1

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 2

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 3

Hi Mark, You shouldn't need to use the Furrion 7-Way Vehicle Power Adapter part #FR87PR because your 2018 Ram 2500 is from the fourth generation of the Ram 2500 before they did the huge overhaul that changed the circuits and resulted in the newer…

view full answer...

Answer 4

A keen observation indeed, Brett. The mounting hole spacing on the Square D-Ring Tie-Down Anchor #ABS69FR is 3" horizontally and 3-1/4" vertically. I edited a picture for you to help illustrate.

view full answer...

Answer 5

Hey Chris, you'd actually be limited by the PSI rating of the valve stem used in the Dexstar Mod Wheel part #DEX69FR long before you'd find the limit of the wheel itself. We have higher PSI valve stems like the part #AM20906 that you could…

view full answer...

Answer 6

So after quite a bit of research it seems that the Trostel 300-156-6 seals you mentioned are quite old and have not been around for some time. The best I could find was that they are 3.00" in outer diameter, and I did manage to find a customer…

view full answer...

Answer 7

The B&W ball #BWHB94005 is a 2-5/16 inch diameter ball which is the standard size for a gooseneck trailer coupler so it can be used. The shank for this ball is 1-1/2 inches in diameter and 2-3/4 inches long. The ball has a 1 inch rise and the…

view full answer...

Answer 8

The part number supplied looks like it's coming back to the Raybestos FRC11046 brake calipers which as you are aware are not available anymore. That being said, we don't have any replacement parts for these braking assembles as we've…

view full answer...

Answer 9

When I reached out to the Dometic they informed me that the foot pedal itself is not replaceable. Which means you can either try to rig something up to get it to work, or you will have to replace the entire toilet assembly. If you're ok with…

view full answer...

Answer 10

Removing old conspicuity tape can be difficult. To remove the top layer of the tape you will want to use a heat source such as a heat gun or blow dryer to warm it up and then use a scraper to scrape the top of it off. Once the tape has been remove…

view full answer...

Recommended Amber and Red Marker Lights w/a Grommet for a 3" Diameter Hole

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching