Replacement Tail Lights And Trailer Wiring Harness For Malone MicroSport Trailer MPG460G

Question

Question:

Hello, I purchased a Malone trail from you. Order 110954329, MPG460G. I need to purchase a passenger side replacement tail light, and a new electrical harness plug, the one that attaches to car. But can not find them. Thanks you, Geoff

asked by: Geoffrey K

0

Expert Reply:

Hey Geoffrey, thanks for reaching out. Yes, we do offer replacement taillights, and a taillight kit for the Malone MicroSport Trailer # MPG460G. We can do just a single light, but if you are needing a new wiring harness too, it'll be best to get the full kit since it comes with everything. Here are the part numbers:

- Combination LED Trailer Tail Light - Submersible - 6 Function - 11 Diodes - Passenger Side # STL8RB

- LED Combination Tail Light Kit for Trailers under 80" Wide - Submersible - Driver and Passenger # TLL9RK

The light kit comes with both taillights, license plate bracket, 25' wire harness with 4-flat, and wire connectors. Everything you'd need to replace the lights and re-wire the trailer.

What kind of kayaks do you haul on the Malone?

expert reply by: Jesse M

0

LED Combination Tail Light Kit for Trailers under 80" Wide - Submersible - Driver and Passenger
(click to enlarge)

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 5

That’s a great question Chadwick, and this is one of those situations where the change in technology really matters. The GE Appliances Low-Profile RV AC w/ Heat Pump part #GE26RR will replace your current ARC13AACBL2 setup, but it’s important to know…

view full answer...

Answer 6

If you're just going to be using these chains once or twice then I recommend Titan Chain Cable Tire Chain #TC2029. These are going to be the most cost affective, will fit your 255/45-20 tires, and installs relatively quickly and easily.

view full answer...

Answer 7

Thanks for reaching out Robert, I did some digging and here's what I found. Optronics bracket #A65PB is a single wire design that grounds through the mounting hardware. I checked through Optronics for the 2 wire to find that it's been…

view full answer...

Answer 8

Hey Michael! The 2026 Kia Sportage Hybrid has the 12V battery integrated into the main battery so you won't be making a connection there. What you need to do is run the #C59236 hot lead to the 12V positive jump terminal under the hood. Everything…

view full answer...

Answer 9

A trailer that is over 80 inches wide is required by DOT regulations to have rear clearance lights. An over 80 inch taillight kit, like part #TL16RK, will have the side clearance light built into it. An under 80 inch taillight does not have the…

view full answer...

Answer 10

Although I don't have any reference information that would tell me the part or crossover number for a lamp on your Haulmark trailer, I found online that the #MC65ARB you referenced would be an identical replacement. To be sure, take a quick…

view full answer...

Answer 11

The installation instructions for the Universal Installation Kit #ETBC7 is a bit generic, and that's on purpose. Since each vehicle is different we just try to give a general overlay of what circuits the different wires need to be connected to -…

view full answer...

Answer 12

Hey Joseph! That is a 3,500 lb Lippert axle so you can use the Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle #BK2-100. If you prefer a Timken kit made in the USA the #TMK52VR is also available. Both come with…

view full answer...

Replacement Tail Lights And Trailer Wiring Harness For Malone MicroSport Trailer MPG460G

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching