Bracket and wiring for Optronics Trailer Clearance or Side Marker Light MCL165AB
Updated 04/14/2026 | Published 04/06/2026
Products Featured in This Question
Question:
Where can I find the part number for the matching 2 wire base this light attachs to, please?
asked by: Robert H
0
Expert Reply:
Thanks for reaching out Robert, I did some digging and here's what I found.
Optronics bracket # A65PB is a single wire design that grounds through the mounting hardware. I checked through Optronics for the 2 wire to find that it's been discontinued.
Optronics # MC44AB trailer side marker light is a 2 wire alternate option.
What kind of trailer are you replacing this light on; boat, utility, travel trailer?
expert reply by:
James D
0
Product Page this Question was Asked From
GloLight Thinline LED Trailer Clearance or Side Marker Light - Submersible - Rectangle - Amber Lens
- Trailer Lights
- Clearance Lights
- Marker
- Rectangle
- Surface Mount
- Submersible Lights
- LED Light
- 3-7/8L x 1-1/4W Inch
- Amber
- Optronics
more information >
Continue Researching
- Search Results: tie down straps
- Search Results: license plates and frames
- Search Results: fasteners
- Search Results: glo light
- Search Results: 1/2" lug nuts
- Search Results: 7 way cord 7 way rv
- Search Results: lug nut
- Q&A: Looking For Replacement Amber Marker Lights For 2010 Winnebago Adventurer 32h
- Q&A: Replacement Mounting Bracket for a GloLight Thinline LED Marker Light MCL165AB
- Shop: LED Combination Tail Light Kit for Trailers under 80" Wide - Submersible - Driver and Passenger
- Shop: Combination LED Trailer Tail Light - Submersible - 6 Function - 11 Diodes - Passenger Side
- Shop: Combination LED Trailer Tail Light - Submersible - 7 Function - 14 Diodes - Driver Side
- Shop: Vehicle Lights
- Shop: Mighty Cord 7-Way RV-Style Trailer Connector w/ Molded Cable - Trailer End - 6' Long
- Q&A: Where to Mount GloLight Thinline LED Trailer Clearance Light to Also Function as Side Marker Light
- Shop: Right Angle 2-Wire Pigtail for Optronics Trailer Lights - 2-Prong PL-10 Plug - 6" Lead
- Shop: LED Combination Trailer Tail Light - Submersible - 8 Function - 21 Diodes - Square - Driver Side
- Shop: 35 Ft 4-Way Trailer Wiring Harness - Wishbone Style - 42" Ground
- Video: Complete Breakdown of the Identification Light Bar for Trailers over 80" Wide
- Video: Erickson Cam Buckle Tie-Down Strap w/ S-Hooks Spec Review
- Video: Curt 7-Way to RV Socket LED Circuit Tester Review
- Video: Review of the Combination LED Trailer Tail Light
- Video: Combination LED Trailer Tail Light Review
- Video: Curt Push-To-Test Trailer Breakaway Kit Installation - 2017 Grand Design Solitude Fifth Wheel
- Shop: Suspension Enhancement
- Video: A Look at the Terran Industries Electric Trailer Brakes
- Q&A: Recommended Replacement AC System for a GE ARH15AACBL2 AC Unit
- Q&A: Recommended Bunk Slicks for Boat Trailer Bunks
- Article: Trailer Wiring Diagrams
- Q&A: Marker Light Dimensions Without Grommet PET45FJ
Kevin
4/14/2026
You’ll need some small countersunk screws to mount that base. If the screw head is too “tall” the lights will not snap into the base properly. Would be nice to include a specialty sheetmetal screw with the base.