Availability Of Lippert On-The-Go Ladder Receiver Bracket

Question

Question:

Where/how do I purchase a Lippert On-The-Go Receiver Bracket?

asked by: Amy D

0

Expert Reply:

Hey Amy, thanks for reaching out. As far as I am aware, those Lippert ladder receivers are only installed from the factory and are not available to purchase aftermarket. If you contact Lippert directly, they may be able to provide one, but I have never seen those for sale as an over-the-counter item.

expert reply by: Jesse M

0

Answer 1

The 4-Leaf Double-Eye Spring part #e44SR is what I recommend using to replace your Dexter Leaf Spring 072-078-00. It's the same length but a slightly higher capacity, 4,400 lbs vs. 5,000 lbs which is not much so it won't really affect the…

view full answer...

Answer 2

Hey Dennis, The bracket the mounts to the trailer wall would need to be installed at the factory and unfortunately isn't an option aftermarket. These are relatively new so I'm assuming after enough people complain to Lippert they'll start…

view full answer...

Answer 3

The clip that you are talking about that is on your leaf spring, like part #e54SR, is called the rebound clip. It keeps the main leaf spring from breaking on a rebound. Typically the band is located on the front-most side of the trailer but it…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 11

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Availability Of Lippert On-The-Go Ladder Receiver Bracket

Product Page this Question was Asked From

Continue Researching