Flat Tow Setup for a 2014 Jeep Wrangler with Factory Standard Bumper

Question

Question:

I have a 2018 Thor A.C.E and I want to tow my 2014 4 door jeep wrangler. I need the right tow system and how to how it up. I need it before May 30.

asked by: SHERREL G

0

Expert Reply:

We got you covered Sherrel, thanks for reaching out!

If your Jeep Wrangler has a different bumper than the standard factory, please let me know because that would change which base plate is compatible with your vehicle.

This flat tow setup is for a 2014 Wrangler with the standard factory bumper:

-Blue Ox Base Plate Kit # BLU53FR

-Blue Ox Avail Tow Bar # BX7420

-Blue Ox 7' Safety Cables # BX88197

-Hopkins Custom Tail Light Wiring Kit # HM39VR

-Roadmaster Battery Disconnect # RM-766

-Blue Ox Patriot Portable Braking System # BLU37TR

-Roadmaster Battery Charge Line Kit # RM-156-25

The Blue Ox base plate has removable arms that directly connects to the Avail tow bar.

For wiring, the Hopkins custom kit avoids splicing wires and plugs into the factory taillights for a easy install.

The Blue Ox Patriot # BLU37TR is a good option if you prefer a portable braking system that can move between vehicles and is easy to use with a straightforward setup.

The charge line is highly recommended on Wranglers since the supplemental braking system and vehicle electronics can slowly drain the battery during long travel days.

Got any trips planned once the Wrangler is ready to tow?

expert reply by: James D

0

Harold

5/22/2026

This is the same hookup I use for my Gladiator and I have no complaints about it. I have used the Blue Ox tow system for about 5 years, first on my 2003 Wrangler, and now on the 2023 Gladiator. The base plate is not really difficult to install, but the right tools are a must. A couple of holes have to be drilled and if you have the metal shield at the bottom of the bumper, it has to be cut to allow for the base plate. I did mine in my garage in about 3 hours or so.

James D.

5/22/2026

@Harold That's great information, really appreciate your insight!

Gerald

5/22/2026

Follow their recommendations. Have it on my 2026 Gladiator, and works perfectly. Glad I have these products, works perfectly!

James D.

5/22/2026

@Gerald thanks for the feedback and we appreciate you choosing etrailer!

Answer 1

Hello Roy, thanks for reaching out. Yes, we do have a Blue Ox base plate that will work on your 2021 Jeep Gladiator Rubicon with the factory steel bumper and Warn winch. For that you'll need the following: - Blue Ox Base Plate Kit - Removable…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 5

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 8

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 9

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 10

Hello Dan, Great question. When you’re comparing the Firestone kits #F59VV and #F2582, they both technically fit your 2025 F-150, but they are designed around different mounting locations and truck configurations. The #F2582 is the traditional…

view full answer...

Answer 11

Hey Jeff, I would strongly recommend the SumoSpring kit part #SS96EV for your 2025 Nissan Frontier. This will give you the support you are looking for without causing the ride quality to be overly harsh which the Timbrens are known to do. Install is…

view full answer...

Answer 12

Hey Fernando, I'd be happy to help you pick out the correct Timbren rear suspension kit for your 2023 Toyota Tacoma TRD that will be towing a trailer. Really it comes down to two options. You would want the part #TTORTUN4L for if you have the 3…

view full answer...

Flat Tow Setup for a 2014 Jeep Wrangler with Factory Standard Bumper

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching