Bearing Buddy Recommendation For Kodiak Disc Brake Assembly With 1.98 Inch Hub Bore

Question

Question:

Looking to buy this kodiak brake kit http://www.etrailer.com/p-K1HR35DS.html what are the correct stainless bearing buddies to buy for this?

asked by: Pete Z

1

Helpful Expert Reply:

The Bearing Buddy you will need to order for the Kodiak Disc Brake Assembly, part # K1HR35DS, is part # BB1980A-SS. These are designed to work with a hub bore that measures 1.98 inches, and have a lifetime warranty.

I have included a link to an installation video you can check out.

expert reply by: Jeffrey L

1

Answer 1

For a disc brake model with an electric reverse lockout solenoid you can use #099-175-20. This would be a great replacement solution.

view full answer...

Answer 2

The Trailer Idler Hub Assembly for 3,500-lb E-Z Lube Axles, #AKIHUB-545-35-G-EZ-K, does not come fully grease. The bearings will need to packed at the time of installation. I recommend using the LubriMatic Marine Trailer Wheel Bearing Grease, #L54FR…

view full answer...

Answer 3

For a disc brake model with an electric reverse lockout solenoid you can use #099-175-20.

view full answer...

Answer 4

The Kodiak XL ProLube Kit for 3500-lb Axles #XLPROLUBE1980KIT that you referenced would work to convert the hubs of your Kodiak Disc Brake Assembly #K1HR35D to oil bath hubs. Oil bath setups are usually found on higher capacity axles, but they would…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Bearing Buddy Recommendation For Kodiak Disc Brake Assembly With 1.98 Inch Hub Bore

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching