Instructions for Replacement Locking Pins for Original SwayPro Weight Distribution Hitch Head

Question

Question:

How to replace the revits in blue ox hitch head?

asked by: Donald S

0

Expert Reply:

Hey Donald, I attached a picture with the install instructions for the Replacement Locking Pins for Original SwayPro Weight Distribution Hitch Head # BLU93QV for you to check out. Let me know if you still have questions!

expert reply by: Jameson C

0

Instructions
(click to enlarge)

Answer 1

The nut on a hitch ball with a 1-1/4 inch shank takes a wrench with a 1-7/8 inch socket. You will need to torque all hitch balls with a 1-1/4 inch shank, like 2-51/6 inch hitch ball #CB28Z, down to 450 ft/lbs.

view full answer...

Answer 2

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 3

Hey Steve, Yes The Big Truck Big Rv Scale #BTBRV004 is hydraulically operated to measure the tongue weight. No electronics or springs inside of it, overall a great scale. What kind of trailer are you towing?

view full answer...

Answer 4

I can end this debate for you real fast! Trailer tires, which will have an ST in front of the size, should always be inflated to the maximum psi indicated on the tire. Trailer tires usually do not have a recommended and maximum psi indication so I am…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 12

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Instructions for Replacement Locking Pins for Original SwayPro Weight Distribution Hitch Head

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching