Looking for Hitch Mounted Skid Roller for 3 inch Hitch Tubing

Question

Question:

I have 2026 Entregra Esteem 29V. It has a 3 hitch tubing. Do you have a Hitch Mounted steel rollers for 3 tubing?

asked by: Robert B

0

Expert Reply:

Hey Robert, we don't have any roller wheels that have large enough U-bolts to fit around 3 inch hitch tubing so best option would be a weld on roller like the Ultra Fab part # UF48-979023. Are you dragging on your driveway?

expert reply by: Jameson C

0

Robert B.

4/15/2026

I am not dragging the driveway. I just wanted some extra protection since the RV sits low in my opinion. Thank you

Jameson C.

4/15/2026

@RobertB that makes sense!

Dan W.

4/16/2026

I purchased the weld on steel rollers and they work great and look great too.

Mark G.

4/16/2026

I also purchased 3 weld on steel rollers and installed them on the rear of my 5th wheel frame. I have a 44' 5th wheel and the rear will drag on inclines(like my driveway). These wheels work great on hard surfaces. They will still drag on soft dirt, gravel or rocks though. Definitely recommend them if you will be on hard surfaces.

Jameson C.

4/16/2026

@DanW thank you for the feedback!

Answer 1

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 4

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 5

Hey Ian, great to hear from you again! The differences between the MORryde CRE3000 #MR87ZR and AllTrek 4000 #MR89DR that fit a 33" wheelbase is the height between the hanger and equalizer bolts, and the amount of travel the suspension style will…

view full answer...

Answer 6

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 7

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 8

Hey Jim welcome back. To determine if you need the TorkLift Camper Anchor Relocation Kit item #TLA7004, you'll have to take a measurement. You'll want to measure from the front bumper of your Palomino HS2902 to the center of the rear anchor…

view full answer...

Answer 9

Hi Travis; those look pretty flat so I don't think 26" would do it either. The 25-1/4" long #EM86RB you ordered will be a better fit. Completely flat these would have a similar measurement at just over 26" which is in line with…

view full answer...

Looking for Hitch Mounted Skid Roller for 3 inch Hitch Tubing

Product Page this Question was Asked From

Continue Researching