Base Plate Kit to Flat Tow 1997 Suzuki Sidekick 4WD 2 Door

Question

Question:

I need a baseplate for a 1997 Suzuki Sidekick, 4WD, 2 door. All listings I see are for 4 door.

asked by: joe b

0

Expert Reply:

Hey Joe, we have the Roadmaster base plate kit part # 118-15 that is a confirmed fit for the 1997 Suzuki Sidekick 2 door. Do you have a tow bar and everything else needed to flat tow the vehicle yet?

expert reply by: Jameson C

0

Answer 1

We offer three different base plate kits for your 1997 Geo Tracker 2-Door that will fit as long as your Tracker is not equipped with brush guards. The link provided will take you to our page for all base plate kits. Roadmaster offers a choice of…

view full answer...

Answer 2

The correct base plates for your 2-door 1997 Geo Tracker to use with your Roadmaster StowMaster Tow Bar #RM-501 are the following: - Roadmaster Crossbar-Style Base Plate Kit #118-8 Along with the base plates you'll also need safety chains,…

view full answer...

Answer 3

If the crossover tube on your 1996 Suzuki Sidekick 2-door is open you will need to use base plates #118-3. But you mentioned that it is open with a bracket welded on each side. If that bracket is not blocking the openings on the crossover tube then…

view full answer...

Answer 4

The original Falcon tow bar, the Falcon 5250, has been discontinued for a few years now and was replaced by the Falcon 2, #RM-520 with upgraded components. Otherwise it functions basically the same was as the original Falcon. Both are RV mount tow…

view full answer...

Answer 5

The Curt tow bar wiring kit part #C63CR that you referenced can install on a vehicle that has separate taillights like you have but there is a different wiring required when installed on a vehicle like then instead of a combined setup. You would run…

view full answer...

Answer 6

To make your etrailer SD Non-Binding Tow Bar for Duncan Base Plates - RV Mount - 2" Hitch - 6,000lbs #e24ZR compatible with your Roadmaster Crossbar-Style Base Plate Kit #1009-1 you'll need to first unbolt both clevis from the arms of the…

view full answer...

Answer 7

There is a suggested and common method for 6 function trailer wiring. You will have the following functions: Right Turn, Left Turn, Ground, Tail/marker, Brake, Battery. I have included a help article on trailer wiring that includes a diagram and…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Base Plate Kit to Flat Tow 1997 Suzuki Sidekick 4WD 2 Door

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching