Replacement 10-36 Dexter Grease Seal for 2022 Grand Design Reflection

Question

Question:

2022 Grand Design Reflection- current seal shows Dexter number 010-036-00 is a match, part number DX72UR?

asked by: Scott R

0

Expert Reply:

Hey Scott! Yes, the Dexter Grease Seal for 12" x 2" Hubs - 2.25" ID - 3.376" OD # DX72UR is the same as the 010-036-00. This is a pair of seals so it is under a different part number, technically Dexter K71-305-00. They have the same inner and outer diameter as the # 10-36 which is the same as Dexter 010-036-00 so they will work as a replacement.

Are you getting your Reflection ready for spring/summer? Any big trips coming up? If you need anything else let me know in the comments below.

expert reply by: Robin H

0

Dexter Grease Seals
(click to enlarge)

Bryan D.

3/26/2026

They worked perfectly on my Dexters.

Scott R.

3/26/2026

Yes, we are heading from Washington to Maine this summer. Just did a trip Alaska

Robin H.

3/27/2026

@ScottR that sounds like an incredible trip. Alaska and now Washington to Maine is about as good as it gets for putting a Reflection to work! Have a safe trip, and if you run into anything along the way don't hesitate to reach out.

Answer 1

A bearing, no matter where it is made, has to meet certain standards for use in the United States. With that said there are some cases where despite having to meet these standards, the US made product is better. When it comes to bearings though I…

view full answer...

Answer 2

Welcome back, Paul! The Dexter Grease Seal for 12" x 2" Hubs - 2.25" ID - 3.376" OD - After 1998 - Qty 2 #DX72UR is the K71-305-00 from Dexter. We had to change the part number as it was very similar to another part, but we get…

view full answer...

Answer 3

Hey Scott! The correct bearing kit for your Dexter 6k axle is the Bearing Kit, 15123/ 25580 Bearings, 10-36 Seal #BK3-100. If you want the Dexter version it is the #DX26ER. What kind of trailer do you have?

view full answer...

Answer 4

Hey Ryan! The best grease seal replacements for your Dexter K71-305-00 are the Grease Seals 10-36 (pair) #RG06-070 which have the exact dimensions you're looking for and are the "tried and true" go-to that we carry.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Replacement 10-36 Dexter Grease Seal for 2022 Grand Design Reflection

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching