Can The Demco Hydraulic Brake Actuator DM8102511 Be Equipped With Electric Lockout?

Question

Question:

Can this brake actuator be equipped with an electric lockout?

asked by: LeeRen R

0

Expert Reply:

Hi LeeRen!

The Demco Hydraulic Brake Actuator w/ Drop - Drum - Zinc - 2-5/16" Ball - 12,500 lbs # DM8102511 can definitely be equipped with an electric lockout. What you are looking for is the following part:

Reverse Lockout Solenoid Kit for Demco Hydraulic Brake Actuators - Non-Bypass # DM5837

This includes the lockout solenoid and a shroud/cover to keep it protected from the elements. There is already an adapter on the back of the actuator (see included image) that will allow this to be screwed right in as well. So the install will be quick and easy!

Are you wanting this for a boat trailer? Tends to be what most people use this kind of actuator with, but not always.

expert reply by: Lazer S

0

Demco Hydraulic Brake Actuator DM8102511
(click to enlarge)

Answer 1

In order to convert your Demco Hydraulic Brake Actuator w/ Drop #DM8102511 to work with disc brakes you'll just need to swap the master cylinder out with the Replacement Master Cylinder w/ Bypass Electric Lockout for Demco Actuators #DM5918. This…

view full answer...

Answer 2

Hey David, all you need to convert your drum brakes to disc is that kit, the Hydrastar Disc Brake Kit w/ Actuator for Tandem Axle Trailers #HYD34VR you were looking at. This kit includes the new actuator, brake lines, fittings, and the new rotors /…

view full answer...

Answer 3

If you remove or puncture the metal check valve from your current master cylinder you will essentially have a disc brake master cylinder. What you will need to do is remove the large snap ring from the front of your actuator where the brake line…

view full answer...

Answer 4

When bleeding the brakes on a surge actuator, such as the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout #DX56FR, you want to start by making sure there is fresh fluid in the reservoir then press a screw driver against the rod in the access…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Can The Demco Hydraulic Brake Actuator DM8102511 Be Equipped With Electric Lockout?

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching