Does Trailer Hub and Drum Assembly for Lippert ABS System Include Spindle Nut

Question

Question:

Looking at purchasing the LC49PX replacement hub does this come with a axel nut? If not what axel nut do i need to get? 7K axels with ABS 9/16 studs Thanks

asked by: Cody R

0

Expert Reply:

Hey Cody! A spindle nut is not included with the Trailer Hub and Drum Assembly for Lippert ABS System # LC49PX. Your typical #42 spindle on a 7k axle will have a 1" diameter on the threads so you can use the Trailer Spindle Nut 1" # 165686.

If you need replacement brakes to go with the hubs those would be the # LC83PX. The brakes do not include sensors so you will have to carry them over from the old brake assemblies.

Did something happen to your hub or is it just worn out from a lot of use?

expert reply by: Robin H

0

Lippert ABS Hub and Drum
(click to enlarge)

Answer 1

Hey Mark! From what the Grand Design parts site shows your 2023 Momentum 395MS has 7k Lippert axles. The correct replacement is the Trailer Hub and Drum Assembly for Lippert ABS System #LC49PX. Do you just need the hub/drum assembly or do you need…

view full answer...

Answer 2

Great question, Nate. Yes, the Brinkley Z 3100 comes standard with Lippert 7,000-lb axles and the Lippert ABS system from the factory, so these #LC83PX brakes are likely what’s already on your rig. If you're hearing squealing or grabbing, this…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 9

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Hi Phil! The main difference between the etrailer Easy Grease Trailer Hub and Drum Assembly #AKHD-865-7-2-EZ-K and the Dexter Trailer Hub and Drum Assembly #42866UC3-EZ is where they are made. Ours are made over seas and Dexter hubs are made here in…

view full answer...

Does Trailer Hub and Drum Assembly for Lippert ABS System Include Spindle Nut

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching