Question

Question:

I have a 2005 Itasca Cambria and cannot find an electric brake controller for that model. The RV has been modified to tow up to 8500 pounds and has a 7-pin connector installed, but no electric brake controller. What would you recommend?

asked by: Jack C

0

Expert Reply:

Hey Jack!

One of the easiest controllers to install, especially for an RV, is the Redarc Tow-Pro Liberty. The only thing visible on your dash is going to be the control knob. If the 7-way was a factory plug then you want to get part # RED96CR. It comes with a custom harness to plug in to a harness that will be under your dash. I included a picture that shows different locations but the plug on your RV would be in location "B".

Now, if the 7-way was installed at a later date and isn't factory, then you want to get part # RED24FR, which is the brake controller itself, and part # RED69FR, which is the universal harness that would need to be spliced into the RV's wiring.

I also included a picture a fellow RV owner sent us showing where they mounted their knob. Kind of an unique location but very accessible.

What other projects do you have lined up for your camper? Sounds like you're getting ready for some fun adventures!

expert reply by: Gwendolyn Y

0

OEM Dash Harness Location
(click to enlarge)

Redarc Knob
(click to enlarge)

Answer 1

If you are unsure if you have the tow package or not, the only way to find out for sure would be to contact a dealership with your VIN. With certain vehicles we can sometimes check to see if certain electrical components are present, like a 7-way…

view full answer...

Answer 2

If the trailer is less than 1 inch off of being perfectly level either up or down then it will be perfectly fine. Having it slightly higher would be better because presumably the tongue weight of the trailer will pull it down a little. You could also…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

Hey Tim welcome back! Your ARH15AACBL2 GE AC unit has the old 410a refrigerant in it so the GE Appliances item #GE64FR you were looking at isn't going to work as a replacement. The EPA mandated R32 refrigerant has been used in all new AC's…

view full answer...

Answer 10

Hi Richard! The best brake controllers on the market for your 2023 Ford Explorer XLT are going to be from Redarc. They're super easy to use and set up, and they are very reliable. They are the ones to get. Since you said you will be towing a…

view full answer...

Answer 11

Good question, Rick. The #ST28MR blue and #ST88MR white steering stabilizer are tuned for different F-53 weight ranges. The blue version is for 24,000 lb + GVWR, while the white one fits 16,000–22,000 lb chassis. What’s your coach’s GVWR or model…

view full answer...

Answer 12

Hey Ken! The correct wiring harness depends on whether or not you have the brake controller port/plug. Some models did not include the plug so you will have to check your 2025 Ranger and see. There should be four wires coming out of a large wire…

view full answer...

Products Featured in This Question

Continue Researching