Replacement for Grease Seals Labeled Dexter 10-10-B

Question

Question:

Hello, I am trying to repack the bearings on my triple axle trailer. The old seals are labeled Dexter 10-10-B. Do you stock these seals or any functionally equivalent? Thank you

asked by: Jeremy T

0

Expert Reply:

Hey Jeremy! The Dexter 10-10-B is the same as the standard Dexter 010-010-00 grease seal. For a replacement you can use the Grease Seal - Double Lip - 2.125" ID - 3.376" OD # RG06-090.

Do you just need seals or do you need bearings as well?

expert reply by: Robin H

0

RG06-090 Grease Seals
(click to enlarge)

Answer 1

I may have an option for you but mobile home axles are considered a one-time use only product and are not designed to be used on a standard trailer. Therefore, there are no hub conversion kits for them that will allow you to use standard…

view full answer...

Answer 2

I was unable to find an order number so I'm not certain exactly what you are referring to, but in general a flat washer such as Washer For 1" Spindle #SW1000 will go between the outer bearing of your hub and the nut that holds it on, which…

view full answer...

Answer 3

The manufacturer of the TruRyde bearing and seals we carry like what come in the kit #BK2-100 is TRP International.

view full answer...

Answer 4

Hey Larry, below I have the entire torque process for the spindle nut of your 7k Dexter axle hub. It's not just as simple as running the nut down to a certain torque value though as it needs to allow the hub to spin. 1. After placing the hub,…

view full answer...

Answer 5

For a hub/drum that will fit your Lippert 5,200 lb axles you would want the hub part #AKHD-655-6-EZ-K that have the same 6 on 5-1/2 inch bolt pattern you said you have. For a self-adjusting brake assembly for the right hand side you would want the…

view full answer...

Answer 6

When our installers replace a trailer hub, there isn't a set torque spec used when tightening the spindle nut. The hub is placed on the spindle, making sure the inner and outer bearings are correctly seated. The spindle nut is then run down until…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Replacement for Grease Seals Labeled Dexter 10-10-B

Product Page this Question was Asked From

Continue Researching