UWS Toolbox that Can Fit Under BAKFlip Tonneau Cover

Question

Question:

Will this tool box fit under a BAKFlip tonneau cover - MX4 GEN 3 - 8foot 2inch Bed × 1? How do I secure it to the truck?

asked by: James P

0

Tonneau Cover
(click to enlarge)

Expert Reply:

Hey James, BAKFlip tonneau covers are going to interfere with opening the lid of the UWS Truck Bed Chest - Wedge Series - Offset Lid - Notched Box # UWS01048. Instead you can use a toolbox like the UWS Truck Bed Chest # UWS08297 or the # UWS08298 for black. These are also low enough that your tonneau cover and it's rail system wouldn't interfere with from underneath as well.

expert reply by: Jameson C

0

Rob

2/13/2026

It fit in my 2025 Ram 2500, but I had to notch the rails so I could open the lid. Worked out great.

Jameson C.

2/16/2026

@Rob good to know! Thanks for passing that along!

Answer 1

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 2

Connection three 10-gauge wires together is going to be best accomplished by soldering the connections as this is the most secure method. We have a solder gun that comes with solder as well with part #PTW2012. I realize that not everyone knows how to…

view full answer...

Answer 3

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 4

I recommend using at minimum a 12 gauge wire like #12-1-1, but preferably 10 gauge wire like #10-1-1. When you try to run 12v power for electric brakes through a thinner 14 gauge wire to power something like your brakes it overloads the wire and…

view full answer...

Answer 5

The overall height of the UWS Truck Bed Chest #UWS01047 is 17-1/4 inches which is going to be shorter than the height of your truck bedrails so it will pretty easily fit underneath your tonneau cover. Now without knowing the length of your bed and…

view full answer...

Answer 6

Hello again Norm, Thank you so much for the picture, it is most helpful since I wasn't able to get any information off of the serial number. Yes, you found the correct one, the Replacement Toilet Bowl Seal Kit for Dometic Sealand and VacuFlush RV…

view full answer...

Answer 7

In order to pick out a direct replacement for the landing gear on your 2009 Bighorn 3055RL we would need to know the distance between the mounting brackets. Otherwise you could just have the brackets removed from your trailer by a qualified welder…

view full answer...

Answer 8

The UWS Tool Box #UWS01048 does not have any fasterners or mounting hardware included or recommended for use by the manufacturer, and will typically just sit in place. The box just slides into place, but if you wanted you could source your own…

view full answer...

Answer 9

We do carry the UWS Truck Bed Toolbox - 5th Wheel Series Chests in Black #UWS01066 and Polished Aluminum #UWS01042 which are specifically designed to work with 5th wheel hitches. Both are confirmed to fit your 2021 Ford F-350 Super Cab 4x4 dually…

view full answer...

Answer 10

Hey Mark, there isn't a way to use a Bedslide with a gooseneck but I was able to find that there is a way to use a CargoGlide with one if you use the part #CGGN-1 which is something that has to be special ordered from them. At this time we…

view full answer...

Answer 11

Hey Heath, thanks for reaching out! The Curt A20 #C55DR and the B&W Companion #BWRVK3670 you're looking at are both excellent 5th wheel hitches, but I have to go with the Companion in this case simple because it is more robust and has a…

view full answer...

UWS Toolbox that Can Fit Under BAKFlip Tonneau Cover

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching