Looking for Lug Nuts for Trailer Wheel and Tire Size LT235/85-16

Question

Question:

NECESITO TUERCA Y PERNO PARA LA LLANTA LT235-85R X 16 VIN 1S9GS4025CW873124 NECESITO 48 I NEED A NUT AND BOLT FOR THE LT235-85R X 16 WHEEL VIN 1S9GS4025CW873124 I NEED 48 I have photos of the bolts and measurements in case you need them, and I can send them to you via WhatsApp

asked by: JOSE L

0

Expert Reply:

Hey Jose, that wheel and tire size can be intended for use with a 1/2 inch lug nut like the part # DE55KR or a 9/16 inch lug nut like the part # DE35KR so it really depends on what your hubs are designed for.

expert reply by: Jameson C

0

Jameson C.

2/10/2026

Hey Jose, did you find out whether your hubs use the 1/2-inch or 9/16-inch lug nuts for your LT235-85R x 16 wheels? Knowing what worked could help others trying to match their wheel hardware.

Jose G.

2/10/2026

@JamesonCI already found them, thanks for the attention

Jameson C.

2/10/2026

@JoseG right on!

Answer 1

Hey William, thanks for reaching out. We do have the self-adjusting brake assemblies that go with the K08-219-9B hubs you mentioned. Here is the exact part number you'll need: - Dexter Nev-R-Adjust Electric Trailer Brakes - 12" - Left/Right…

view full answer...

Answer 2

Hey Lee. You'll need to pull the hub and measure the inside of it if you can't find a part number on the brake assemblies themselves. You'll need the diameter of the hub and the width. Most modern brakes, like the item #23-180-181 you…

view full answer...

Answer 3

We have many styles and sizes of trailer wheel lug nuts shown on the linked page. These are offered in either 60-degree or 90-degree coned profile, in zinc, chrome or stainless and for four different wheel stud diameters. Just click on the feature to…

view full answer...

Answer 4

In order to find the correct replacement hubs for your 2016 Keystone Raptor, since you already know the weight rating of your axle, you need to know what bearings your current hub has. You will need to take apart your current hub assembly and look at…

view full answer...

Answer 5

Typically a trailer axle will have some camber in it - some bend - such that when it is not loaded the tops of the wheels bow outward slightly, with the outside edges of the tire treads making first contact with the ground. This allows that when the…

view full answer...

Answer 6

Trailer tires can be balanced but you should note that normally they are not. What happens most of the times is that the person mounting the tire will line up with light spot of the tire with the heavy spot of the rim and it gets the setup about as…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Looking for Lug Nuts for Trailer Wheel and Tire Size LT235/85-16

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching