What DeeMaxx Disc Brake kit Fits A Reflection 260RD?

Question

Question:

What deemaxx disk break kit for a reflection 260rd rig?

asked by: Robert

0

Expert Reply:

Hello Robert, thanks for reaching out. The correct DeeMaxx Disc Brake Kit for your Reflection 260RD will depend on the axle capacity (often 7,000 lb on that model) and whether your axles have electric brakes already.

For example, if you have 7K axles with electric brakes and you want to switch to EOH disc brakes, the DeeMaxx Disc Brake Kit w/ Actuator for Tandem Axle Trailers # DE66AR is what you will need. It includes the EOH actuator, rotors, calipers, hubs, mounting brackets needed for a direct disc conversion.

You will also need to make sure the brake controller in your truck is compatible with EOH brakes. Most aftermarket controllers like the Tekonsha P3 # 90195 work with EOH brakes, but some factory controllers may not.

What truck and brake controller do you use?

If you'd like me to confirm the exact right part numbers, just let me know your axle rating and what kind of brakes you have currently. I am happy to look into it and make sure you get the right thing.

expert reply by: Jesse M

0

DE66AR
(click to enlarge)

Robert

12/22/2025

My truck is a 2024 ram 2500 with factory controller.

Jesse M.

12/23/2025

@Robert Ok perfect that factory controller should work with EOH brakes or it'll have an EOH mode you need to switch to. Just confirm that axle capacity and you will be good to go.

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

What DeeMaxx Disc Brake kit Fits A Reflection 260RD?

Product Page this Question was Asked From

Continue Researching