Will SnapPad Mini Jack Pads SN39FR Fit A 2025 Trade Wind 23 FBT With 5-1/2" Square Jack Feet?

Question

Question:

Hello I have a 2025 Trade Wind 23 FBT. It have 5 1/2 x 5 1/2 square feet is this going to fit... SnapPad Mini Jack Pads for Travel Trailers w/ BAL - 5-1/2 Square Jack Feet - Qty 4 Thanks for your time. Mitch

asked by: Mitchel B

0

Expert Reply:

Hey Mitch, thanks for reaching out. You’re right on target with your measurements. The SnapPad Mini Jack Pads # SN39FR, are made specifically for 5-1/2 inch square jack feet, so they’ll be a perfect match for the setup on your 2025 Trade Wind 23 FBT. Once installed, they’ll give you a wider footprint, better grip on uneven surfaces, and a little added protection for your landing gear.

Just make sure the bottoms of your jack feet are clean before snapping them on so they seat correctly. Other than that, there’s nothing special you need to worry about. They’re a simple upgrade that makes a noticeable difference in stability and convenience.

Let me know if you want help finding any other accessories for your Trade Wind.

expert reply by: Jesse M

0

SnapPad Mini Jack Pads SN39FR
(click to enlarge)

Mitchel B.

12/12/2025

Thanks a lot I will order these in the near future!

Jesse M.

12/15/2025

@MitchelB Glad to help! Feel free to come back anytime you need anything!

Answer 1

Hi Ryan; the Weigh Safe Hitch w/ Built-In Scale for 2.5" Hitch #WS56ZR is designed in the US but manufactured in China. The Weigh Safe ball mounts with the built-in scale are pretty unique so we don't have a USA made option with the same…

view full answer...

Answer 2

For your Replacement Voyager WiSight 2.0 Wireless RV Backup Camera Monitor #ASA27FR (WVSXM70), you can use the Replacement Voyager WiSight 2.0 Wireless RV Backup Camera with Low Light Assist #ASA64YR. These cameras do have the 4 pin connector that…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Will SnapPad Mini Jack Pads SN39FR Fit A 2025 Trade Wind 23 FBT With 5-1/2" Square Jack Feet?

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching