Do You Have a Atwood 15092 AC Control Board?

Question

Question:

I have an atwood AC on a 2022 Georgetown 34m5 that is fried. I am trying to find a replacement board for the Atwood 15092.

asked by: Mike R

0

Expert Reply:

Hey Mike thanks for the picture! We do not have the Atwood 15092 AC Control Board.

I hope you get your AC back up and running. Keep us in mind down the road if you ever need help.

expert reply by: Jerred H

0

Jerred H.

12/8/2025

Hey Mike, were you able to find a replacement board for your Atwood AC? Knowing what worked could help others trying to fix the same issue.

Answer 1

Yes. You've found the right part. The 29/324 378 part number you've referred to off your existing jack corresponds to the Lippert Replacement Level Up Hydraulic Jack - 8,000 lbs - 15" Travel #LC26FR so it will be the correct replacement…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 4

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 11

Hey Donny! For your Dometic Penguin/Brisk Air 15,000 BTU AC model B59516.711C0-MX, the correct soft start is the #DMC93JF. This is designed for Dometic Brisk II electronic air conditioner units with in-wall thermostats.

view full answer...

Answer 12

That’s a great question Chadwick, and this is one of those situations where the change in technology really matters. The GE Appliances Low-Profile RV AC w/ Heat Pump part #GE26RR will replace your current ARC13AACBL2 setup, but it’s important to know…

view full answer...

Do You Have a Atwood 15092 AC Control Board?

Product Page this Question was Asked From

Continue Researching