Replacement Wheel Recommendation for a Fulton Trailer Jack # FTJ120W0301

Question

Question:

do you sell a replacement wheel for this jack? Fulton Round, Snap-Ring Swivel Marine Jack - Weld On - Sidewind - 10inch Lift - 1,200 lbs

asked by: Ed

0

Expert Reply:

Yes we do, for a replacement wheel for your Fulton Trailer Jack # FTJ120W0301 you would want the Replacement Wheel Kit # F6811S00.

expert reply by: Jameson C

0

Answer 1

Hello Adam, thanks for reaching out. It is possible to replace the broken wheel on your Fulton F2 dual wheel jack with part #F500138, but I am sorry to say there is not a foot plate that will work with this jack. Fulton does make a version of the F2…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 5

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

Hey Tim welcome back! Your ARH15AACBL2 GE AC unit has the old 410a refrigerant in it so the GE Appliances item #GE64FR you were looking at isn't going to work as a replacement. The EPA mandated R32 refrigerant has been used in all new AC's…

view full answer...

Answer 12

Hello Jason, thanks for reaching out. Yes, the Kenda Karrier KR53 ST205/75R15 tire with 15" black aluminum wheel #KE58JV does come balanced from the factory. Trailer tire and wheel assemblies are balanced by matching the tire’s high and low…

view full answer...

Replacement Wheel Recommendation for a Fulton Trailer Jack # FTJ120W0301

Continue Researching