Need Wiring Instructions for Wall Remote Switch # VC0533-03-A on Ventadome Roof Vent with 12V Fan

Question

Question:

Hi, I purchased a Ventline Ventadome Roof Vent w/ 12V Fan - Powered Lift - 14-1/4inch x 14-1/4inch and a Wall Remote Switch for Ventline Ventadome Roof Vent. I need some help on wiring the switch. Is there a wiring instruction for the switch. Thanks,

asked by: Bruce B

1

Helpful Expert Reply:

I have attached a wiring diagram for the Ventline Remote Switch, # VC0533-03-A, that is used with the Ventline Ventadome Roof Vent with 12 Volt Fan # V2119-603-00.

expert reply by: Leah S

1

click to enlarge

Answer 1

It is normal to have continuity between the brake(blue) wire and ground(white) wire. The electric trailer brake is an electromagnet when it has power it attracts to the steel inside the hub/drum. If you are having issues with your trailer brakes…

view full answer...

Answer 2

The blue wire coming from the back of your Tekonsha Voyager Brake Controller #39510 is for brake output to the 7-Way connector. This wire should only have power with the brake pedal depressed or the manual override activated on the brake controller.…

view full answer...

Answer 3

I went ahead and hunted down a wiring diagram for the WH6GA water heater, and was able to find a diagram (attached below). This tank has a 10K Btu heating capacity, a 6 gal tank, measures 12-3/4"H x 12-3/4"W x 19-7/8"D, and is a direct…

view full answer...

Answer 4

The Model 32 part number 903211000 you mentioned references a Kwikee 32 series powered double step just like the part #LC3722616 that you referenced so this is what you'd need.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...