Power Roof Vent That Wires To Switch Plate

Question

Question:

Do you offer a bath vent fan that wires into my existing switch plate that has 1 for opening lid and 1 for fan?

asked by: Charlie H

0

Expert Reply:

Yes, the Ventline Ventadome Roof Vent part # V2119-603-00 is designed to wire to a switch like the one you mention part # VC0533-03-A. I have attached a wiring diagram for your reference.

The Ventadome Roof Vent also comes in white part # V2119-601-00.

expert reply by: Heather A

0

click to enlarge

Answer 1

You can utilize a power wall remote switch #VC0533-03-A or #VC0533-02-A (black or white). A rocker switch #BL0108-00 will work and you will need 2 of them. The installation kit #344270KITW will come with screws, tape, and sealant. You will also need…

view full answer...

Answer 2

Hey Rick, The best replacement we have for your 2015 Jayco Greyhawk is the Progressive Dynamics 4000 Series Mini RV Converter w/ Charge Wizard and AC/DC Distribution Panel #PD4045KA. This is rated for 45 Amps so it will be a little more than your…

view full answer...

Answer 3

I have attached a wiring diagram for the Ventline Remote Switch, #VC0533-03-A, that is used with the Ventline Ventadome Roof Vent with 12 Volt Fan #V2119-603-00.

view full answer...

Answer 4

I went out and measured the outside to outside points on the flange for the MaxxAir MaxxFan, part #MA00-04401M, and it's 16-1/4 square. It does fit the standard 14 x 14 vent opening which is what you'll find on most trailers and it's for…

view full answer...

Answer 5

The Replacement MaxxFan Plus 4-Speed Roof Vent with White Lid #MA00-04751KSX is meant to be a direct replacement however not all the necessary hardware is included. The remaining items you'll need is the Key Wall Control part #MA00A03550K,…

view full answer...

Answer 6

Hey Brian. The Seaflo Fresh Water Electric RV Toilet item #SE95CR does not use a standard 3" or 4" RV toilet flange and you will need to purchase new hardware and additional fittings. The 18-3/4" tall x 14" wide x 17-1/4"…

view full answer...

Answer 7

Hey Lexie, the closest thing we have is the #BA65FR. This fits cutouts that are 5-1/4" wide x 4-1/2" tall. The little bit of extra height on your cutout won't be a problem since the face is 5-1/2" tall and would cover the opening.…

view full answer...

Answer 8

Hey Lisa, So while I wouldn't' be able to tell you the exact drop you need for your ball mount when towing with your 2019 Toyota Highlander, but I can tell you how to determine the right one. It's actually really easy as you just need to…

view full answer...

Answer 9

Hey Richard. welcome back! The Go Power Pure Sine Wave Inverter Charger #GP75QR does not include the display. You will need the Go Power PowerTrak Screen #GP64XR to go with it. You will also need the #GP74XR, #GP84XR, and #GP24XR to make all of your…

view full answer...

Answer 10

Happy to help James, thanks for reaching out! Choosing the right M-3 ramp door spring system really comes down to matching your specific trailer and door. The biggest factor is the weight of your ramp door. The spring system is designed to help lift…

view full answer...

Answer 11

Welcome back Rich and thanks for the information! To replace your Sharp Carousel microwave R-820BK-F, I recommend the Greystone Built-In RV Convection Microwave item #GR27FR. It measures 21" wide x 11" tall x 15-3/4" deep.…

view full answer...

Answer 12

I did some digging on your AL KO 7,200 lb axle and it has bearings #28580 and #25580 which means you have a 99 spindle. The only hub we offer that will fit this setup is the part #99865UC3 which is a similar Titan hub but has an 8 on 6-1/2 inch bolt…

view full answer...

Power Roof Vent That Wires To Switch Plate

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching